Block Diagram of the LSISAS6160 Switch | LSI specs

Chapter 1: Overview Serial Attached SCSI and the SAS6160 Switch

LSISAS6160 SAS Switch User Guide

You can connect multiple SAS6160 switches in various topologies to provide failover support and to increase the number of connected devices in the SAS domain. The theoretical upper limit of SAS devices in a domain is 16,000. Each SAS6160 switch can handle 1000 SAS addresses.

The following figure shows a high-level block diagram of the SAS6160 switch.

Temp

Sensor

RTC

Fan Control

Flash

Memory

PBSRAM

Memory

Ethernet

Phy

						4 SAS Lanes (for failover)


		SAS2x36							SAS2x36




		Expander							Expander
		Expander							Expander
		Master							Slave

							Dual Port
							Memory

	32 SAS Lanes								32 SAS Lanes

x2	x2
x2	x2
x4	x4

16 x4 External Mini SAS Connectors

Temp

Sensor

Fan Control

Flash

Memory

PBSRAM

Memory

Figure 3: Block Diagram of the LSISAS6160 Switch

This diagram contains the following functional blocks:

SAS2X36 Expander – This block includes such management functions as routing, device discovery, and zoning. It also includes an embedded version of SDM. This block controls the flow of data through the SAS connectors.

SAS Connectors – The SAS6160 switch has 16 x4 Mini SAS connectors, numbered 0 through 15. It supports connection to SAS devices at link rates of 3.0Gb/s and 6.0Gb/s.

Ethernet Phy – The external 10/100 Ethernet port provides access to the browser-based SDM management application, which sets up storage configurations in the SAS domain, monitors the status of the switch, and runs diagnostic tests. It also provides access to the SDM command line interface (CLI).

Real Time Clock – The battery-powered real-time clock is set at the factory.

Fans – The SAS6160 switch enclosure contains two fans. The fan speed is regulated based on the temperature inside the enclosure. You can monitor the status of the fans with the SDM utility.

Page 8

LSI Corporation September 2010

Image 8

LSI manual Block Diagram of the LSISAS6160 Switch

Contents

LSISAS6160 SAS Switch Revision History Table of Contents SAS Domain Manager Command Line Interface Features Chapter Serial Attached Scsi and the SAS6160 Switch LSISAS6160 Switch LSISAS6160 Resource Management Block Diagram of the LSISAS6160 Switch SAS Phys, Ports, and Connectors Link between Two Single SAS Phys Narrow and Wide SAS Ports SAS Connectors and Cabling Mini SAS 4x Cable Minimize conflicts Only the storage within its zone or zonesAcross the entire Zpsds SAS Zoning Overview Creating SAS Zones Groups and zone sets manually by using the SDM utilityFollowing figure shows a simple example of zoning Overview SAS Routing and Zoning Configuration for Zoning Example Connecting Devices to the SAS6160 Switch Creating Zone Groups Example 1, Multiple Servers and JBODs Example 3, Multiple Servers and a Cascading Switch Example 4, High Availability Example 5, Large Data Storage Topology Example 6, Cascaded Switches Example 7, Switches in a Star Tree Configuration Unpacking the Switch Identifying Switch ComponentsTo interpret the LEDs on the switch Carton contains the following items Installing the SAS6160 Switch SAS6160 ConnectorsCables SAS6160 LEDs Rack. These options are shown in the following figure Mounting Shelf in a Rack Connecting to a Host Changing the Default Static IP Address Setting a Static IP Address Exit SDM-GUI and power cycle the switch Exit SDM-CLI and power cycle the switchUsing SDM-GUI For example Connecting SAS and Sata Hardware Safety Notices 1 FCC Canada Mark Vcci Bsmi 5 CCC Installation and Hardware Setup Safety Notices SDM-GUI Accounts Starting SDM-GUI Options Embedded SDM only supports a single domain File, Server, and Help Menu Options Information is available to both admin and user accounts Views TabFor zoning View End Device Table Alias Table View Zone Groups View Zone Groups View Zone Sets View Zone Sets Domain Tab This section, click the hyperlinks on the Domain tabNode100, and so on Alias Management View/Delete Aliases View/Delete Aliases commandDomain. You also can also this command to delete aliases Connector Wizard Zone set and the two associated zone groupsBox and clicking the Delete button Group to communicate with each other Guide you through the configuration process Maximum number of 248, the wizard displays an error messageCheck box and clicking the Delete button Zone group to communicate with each other Manually Configure Zone Groups Create Zone Group Create Zone Group Time of activation. shows the View Zone Group window View Zone GroupModify Zone Group Delete Zone Group Maximum password length is 32 characters Binary 0, as defined by the SAS 2.0 specificationPassword Matrix View Zone Set window Zone setView Zone Set Modify Zone Set Activate/Deactivate Zone Set Activate/Deactivate Zone Set Window and then clicking Delete Delete Zone Set Devices Tab Device Tree and Properties Tab Properties Tab Selected device. In , the domain properties are shownFollowing figure shows the Properties tab Background loop Environmentals Tab Attached Devices Tab Those connectionsFollowing figure shows the Attached Devices tab Selected expander Following figure shows the Phys tab Zone Group Tab Zone Group Tab This tab contains the following commands Successful updateUpdate Firmware Operations Tab Following figure shows the Enable/Disable/Reset window Enable/Disable/ResetReset Switch Phys Configure IP As shown in the following figures Command Usage Syntax Command arguments SDM-CLI Commands Help command„ help command Domain focus domain name Passwd admin user „ passwd admin„ passwd user Exit „ alias delete „ show alias „ show phy„ show zonegroup „ show zoneset „ zonegroup add name sas addressaliasphy „ zonegroup create name„ zonegroup delete single name „ zonegroup delete all noconfirm Set membership „ zoneset activate name„ zoneset add name zone group zone group „ zoneset create name Sample Output for Show Command „ zoneset passwdSdmcli show alias Sdmcli show alias Calhoun Sdmcli show device Calhoun Sdmcli show domain Sdmcli show phyShow domain Show phy Alias Phy Device Capabilities SAS Address Type Sdmcli show phy CalhounRA Routing Attributes VP Virtual PHY Zone Grp Show phy alias Zoning Active Zone Group Number Zoning Inactive * phy may be assigned to a zone group Sdmcli show phy Lincoln01 Sdmcli show versionSDM-CLI Version SDM-D Version Show phy alias phy Sdmcli show zonegroup ZoneOne#001 Sdmcli show zoneset activeShow zoneset data name Sdmcli show zoneset data ZoneOne Show zonegroup name Xip -i get avail Xip -i 500062b15555557f get exp Troubleshooting