Marantz SR7002, SR8002 manual NEC National Electrical Code

13. Power-Cord Protection – Power-supply cords

should be routed so that they are not likely

to be walked on or pinched by items placed

upon or against them, paying particular

attention to cords at plugs, convenience

receptacles, and the point where they exit

from the product.

14. Protective Attachment Plug – The product

is equipped with an attachment plug having

overload protection. This is a safety feature.

See Instruction Manual for replacement or

19. Object and Liquid Entry – Never push objects

of any kind into this product through openings

as they may touch dangerous voltage points

or short-out parts that could result in a fi re or

electric shock. Never spill liquid of any kind

on the product.

20. Servicing – Do not attempt to service this

product yourself as opening or removing

covers may expose you to dangerous voltage

or other hazards. Refer all servicing to

qualifi ed service personnel.

24. Wall or Ceiling Mounting – The product	25. Heat – The product should be situated away
should be mounted to a wall or ceiling only as	from heat sources such as radiators, heat
recommended by the manufacturer.	registers, stoves, or other products (including
	amplifi ers) that produce heat.

FIGURE 1

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

resetting of protective device. If replacement

of the plug is required, be sure the service

technician has used a replacement plug

specified by the manufacturer that has the

same overload protection as the original plug.

15. Outdoor Antenna Grounding – If an outside

antenna or cable system is connected to the

product, be sure the antenna or cable system

is grounded so as to provide some protection

against voltage surges and built-up static

charges. Article 810 of the National Electrical

Code, ANSI/NFPA 70, provides information

with regard to proper grounding of the mast

and supporting structure, grounding of

the lead-in wire to an antenna-discharge

unit, size of grounding conductors, location

of antennadischarge unit, connection to

21. Damage Requiring Ser vice – Unplug

this product from the wall outlet and refer

servicing to qualifi ed service personnel under

the following conditions:

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have

fallen into the product.

c. If the product has been exposed to rain or

water.

d. If the product does not operate normally by

following the operating instructions. Adjust

only those controls that are covered by

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

GROUND CLAMPS

ANTENNA

LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

POWER SERVICE GROUNDING ELECTRODE SYSTEM

(NEC ART 250, PART H)

	grounding electrodes, and requirements for
	the grounding electrode. See Figure 1.
16.	Lightning – For added protection for this
	product during a lightning storm, or when it is
	left unattended and unused for long periods
	of time, unplug it from the wall outlet and
	disconnect the antenna or cable system. This
	will prevent damage to the product due to
	lightning and power-line surges.
17.	Power Lines – An outside antenna system
	should not be located in the vicinity of overhead
	power lines or other electric light or power
	circuits, or where it can fall into such power
	lines or circuits. When installing an outside
	antenna system, extreme care should be taken
	to keep from touching such power lines or
	circuits as contact with them might be fatal.
18.	Overloading – Do not overload wall outlets,
	extension cords, or integral convenience
	receptacles as this can result in a risk of fi re
	or electric shock.

	the operating instructions as an improper
	adjustment of other controls may result in
	damage and will often require extensive
	work by a qualifi ed technician to restore the
	product to its normal operation.
e.	If the product has been dropped or damaged
	in any way, and
f.	When the product exhibits a distinct change
	in performance this indicates a need for
	service.

22.Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fi re, electric shock, or other hazards.

23.Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

NEC - NATIONAL ELECTRICAL CODE

This Class B digital apparatus complies with Canadian	Cet appareil numérique de la Classe B est conforme
ICES-003.	à la norme NMB-003 du Canada.

DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S. Responsible Party: Marantz America, Inc.

100 Corporate Drive,

Mahwah, NJ, 07430, U.S.A.

TEL: 630-741-0300

Type of Product: AV Surround Receiver

Model:SR7002/8002

AV_060908U1