Marantz SR7002 Auto Power Off, M E M O R Y S A V I N G, Recovery Of Memory, Backup, Auto Power On

Turn ON the TV TUNER and tune in a receivable station.

When the station is received, this unit turns ON and TV is selected automatically.

ENGLISH		AUX2 INPUT
	If you don’t need to connect 7.1 Ch. input terminals
	with multi channel decoder,
	L(front left) and R (front right) inputs terminals are
	available as AUX2 input.
	In this case, You can connect additional audio source
	to AUX2 as other audio input terminals.
			AV SURROUND RECEIVER SR8002

VIDEO ON/OFF

When no video signal is connected to the unit or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.

To select video off, press the AMP button and press the > button until PAGE 4 is displayed. Press the V-

2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input.

3. Turn OFF the power to the TV TUNER and the unit.

4.

5.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

2. The power to the unit switches to STANDBY after approx. 5 minutes.

Notes:

•AUTO POWER OFF is canceled if this unit is set to a source other than TV.

The function reactivates when TV is selected again.

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.

•The S-Video terminal does not support “TV AUTO ON/OFF” function.

CHVOL

OK

LIP.SYNC

PREVMUTE

GUIDE

MENUEXIT

TEST	CH.SEL	SURR
1	2	3
7.1CH	ATT	SPK-AB
4	5	6
DISP	OSD	SLEEP

7 8 9

THX

CLEAR 0 MEMO

Note:

•The LIP.SYSNC feature turns OFF (0 ms) in the SOURCE/PURE DIRECT mode. When the SOURCE/PURE DIRECT mode is deactivated, the set value of the LIP.SYSNC feature is automatically restored.

•Even if you do not correct the time lag manually this way, audio and video are automatically synchronized when the unit is connected to TV or Projectors supporting Auto Lipsync Correction in HDMI 1.3a. For instructions on Auto Lipsync Correction, see page 54.

DUAL BACKUP MEMORY

“MEMORY SAVING” is displayed and the unit’s settings are saved. The stored settings information is retained until Dual Backup Memory is used again and the information is overwritten.

M E M O R Y S A V I N G

Note:

•The following settings values cannot be backed up.

•Main Room Volume

•Multi Room Volume

•Multi Speaker Room Volume

RECOVERY OF MEMORY

Recover backed up settings as follows.

Hold the MEMORY and MENU buttons on the front panel simultaneously for at least 3 seconds.

SURROUND

DIGITAL

AAC

OFF button.

UND RECEIVER SR8002

SURROUND

DIGITAL

AAC

USEPAGE 1 2 3 4

M

D1

D2

D3

D4

D5

LIP.SYNC

Depending on the image device (TV, monitor, projector, etc.) connected to the unit a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can

The unit stores settings information in nonvolatile memory even when the main power supply is turned off. Using the Dual Backup Memory function, you can write settings information to another memory area to back up saved settings for recovery anytime as needed.

BACKUP

“MEMORY LOAD” is displayed and the unit’s stored settings are reapplied.

The unit temporarily enters standby mode. If there is no backup data, “NO BACKUP” is displayed and no data is recovered.

CHVOL

TUNER	CD	CD-R	MD
TAPE	AUX1	AUX2	AMP
		LIGHT
1			2

RC8001SR

Learning Remote Controller

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the unit.

AUTO POWER ON

1. Be sure the TV auto mode is ENABLED. (Refer to page 53:)

interfere with movie and music enjoyment. The LIP. SYNC feature delays the audio signal with respect to the image signal output from the SR7001 to correct the time lag between the sound and image. It can be operated with the “LIP.SYNC” and 1 and 2 cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms). The time lag can be adjusted in 10 ms steps up to 200 ms.

Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.

Set up the unit in the state for which you want to store the settings. Hold the MEMORY and ENTER buttons on the front panel simultaneously for at least 3 seconds.

SURROUND

DIGITAL

AAC

M E M O R Y L O A D

N O B A C K U P

Note:

•Because the following settings values are not backed up, each Volume value is set to Minimum.

•Main Room Volume

•Multi Room Volume

•Multi Speaker Volume

66