ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
| M |
| D1 |
| D2 |
LEARN |
|
NAME | D3 |
MACRO |
|
| D4 |
USE | PAGE 1 2 3 4 |
| D5 |
CH |
|
| VOL |
TUNER | CD | MD | |
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8001SR
Learning Remote Controller
During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics.
(Using the remote controller)
To adjust the tone, press the AMP button and press the > button PAGE3 is displayed.
To adjust the bass effect, press BASS+ (D2) or BASS– (D3).
To adjust the treble effect, TREB+ (D4) or TREB– (D5).
Notes:
•The tone control function is unavailable for the Source Direct, Pure Direct, Headphone, Dolby Virtual Speaker, THX mode, and 176.4/192kHz PCM.
•The tone control function is not available when ACOUSTIC EQ is being used.
•Additionally, tone control is not available during Dolby TrueHD, Dolby Digital Plus, or
TEMPORARILY TURNING OFF THE SOUND
USING THE SLEEP TIMER
| LIP.SYNC |
|
PREV |
| MUTE |
| GUIDE |
|
MENU |
| EXIT |
TEST | CH.SEL | SURR |
1 | 2 | 3 |
7.1CH | ATT | |
4 | 5 | 6 |
DISP | OSD | SLEEP |
7 | 8 | 9 |
| THX |
|
CLEAR | 0 | MEMO |
To program this unit for automatic standby, press the SLEEP button on the remote controller.
Each press of the button will increase the time before shut down in the following sequence.
OFF 10 20 30 40 50
120 110 100 90 80 70 60
The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed.
When the programmed sleep time has elapsed, the unit will automatically turn off.
Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows “SLEEP OFF” and the SLEEP indicator will disappear.
M-DAX (Marantz Dynamic Audio eXpander)
M
D1
D2
(Using the remote controller)
When switching to
When
Each time this button is pressed,
OFF LOW HIGH
Notes:
•
•The
VIDEO CONVERT
ANALOG VIDEO CONVERSION
This unit is equipped to convert video signals for monitor output. Because of this, indifferent of the connection (VIDEO,
UP-CONVERSION FROM ANALOG VIDEO SIGNALS TO HDMI
The
Notes:
If this occurs, set “VIDEO CONVERT” in the | ENGLISH | |
“VIDEO SETUP” menu to “DISABLE”. Next, | ||
| ||
connect the video input signal to the display component |
| |
via the MONITOR OUT terminal under VIDEO and |
| |
the |
| |
the MONITOR OUT terminal under |
|
•The video convert feature constantly monitors input video signals and determines whether to convert the input signals or not. However, some input video signals cannot be detected correctly. If this occurs, set “VIDEO CONVERT” in the “VIDEO SETUP” menu to “DISABLE”.
•For optimal video performance, THX recommends setting the “VIDEO CONVERT” mode “DISABLE”.
CONNECTION EXAMPLE
•When a monitor is connected to the HDMI MONITOR OUT terminal of the unit
VIDEO |
|
or |
|
or component |
|
or HDMI | HDMI |
Notes:
•If the resolution of the component video signal input from the playback device is other than 480i, 480p, 1080i or 720p, images are not output from the HDMI MONITOR OUT terminal of the unit.
•If the resolution of the
•When a monitor is connected to the VIDEO or S- VIDEO MONITOR OUT terminals of the unit
OK
| LIP.SYNC |
|
PREV |
| MUTE |
| GUIDE |
|
MENU |
| EXIT |
TEST | CH.SEL | SURR |
1 | 2 | 3 |
7.1CH | ATT | |
4 | 5 | 6 |
DISP | OSD | SLEEP |
7 | 8 | 9 |
To temporarily silence all speaker outputs such as when interrupted by a phone call, press the MUTE button on the remote controller.
This will interrupt the output to all speakers and the
When the system is muted, the display will show “MUTE” .
D3
D4
USE | PAGE | 4 |
D5
CHVOL
TUNER | CD | MD | |
TAPE | AUX1 | AUX2 | AMP |
|
| LIGHT |
|
1 |
|
| 2 |
RC8001SR
Learning Remote Controller
This function makes up for lost audio content in MP3 or AAC sources (from lossy compression) during playback. Choose one of the following levels for this effect as desired.
“HIGH”: Stronger effect
“LOW”: Weaker effect
“OFF”: Deactivated.
•HDMI video input is only output to the HDMI MONITOR OUT terminal of the unit. If connecting a playback device such as a DVD player to the HDMI input jack, connect the HDMI MONITOR OUT terminal of the unit to a TV monitor.
•This mode is unavailable for the REC out terminal.
•This mode is unavailable for still picture, fast forward and reverse play on video component.
•If, while attempting to use the video convert feature, the unit cannot synchronize with the display device, “NO SIGNAL” appears on the monitor or noise is generated, this feature cannot be used. All of these signs are caused by equipment incompatibility; there is nothing wrong with the unit.
VIDEO |
or |
or component |
HDMI |
VIDEO or
Press the MUTE button again to return to normal operation.
59