![OPERATION OF THE MULTI ROOM OUTPUTS](/images/new-backgrounds/18099/18099163x1.webp)
OPERATION OF THE MULTI ROOM OUTPUTS
WITH THE REMOTE CONTROL FROM MULTI A
Room A output can be operated from a room where the unit (SR7002 or SR8002) is not installed. This requires a separately sold IR receiver. (For connections, see page 37.)
CHANGE THE MULTI ROOM CONTROL COMMANDS
(RC101) FOR MULTIROOM A
(When operating the unit by Multi Zone connected)
•Zone A: MULTI ROOM A Control (Default)
•Zone B: MULTI ROOM B Control
(The SR7002 does not use this zone.)
Change the control commands for each zone.
2. 1.
1. Press SET button and ZONE button until the SEND indicator blinks twice.
Then backlight flashes.
2. Press A zone button.
When the procedure is successful, the SEND indicator will blink twice.
These buttons change a special code of each zone.
POWER ON/OFF ![WITH THE REMOTE CONTROL FROM MULTI B](/images/new-backgrounds/18099/18099163xi7.webp)
![(RC101) FOR MULTIROOM B](/images/new-backgrounds/18099/18099163xi8.webp)
![Manual background](/images/new-backgrounds/18099/18099163xi9.webp)
![Manual background](/images/new-backgrounds/18099/18099163xi10.webp)
![Manual background](/images/new-backgrounds/18099/18099163xi11.webp)
![Manual background](/images/new-backgrounds/18099/18099163xi12.webp)
SOURCE
VOL +/–
MUTE
Tuner mode operation remote code (Refer to page 26)
Notes for the Multi Room System
•If the Tuner (FM or AM) is active in the main room, you can not control any function of the tuner.In this case, You must listen to the same station as the main room.
OSD INFORMATION FOR THE MULTIROOM A SETUP
INFO![Manual background](/images/new-backgrounds/18099/18099163xi28.webp)
Press the INFO button to view the current setup as shown below on a TV monitor connected to MULTI VIDEO OUTPUT.
MULTI ROOM
VIDEO :DSS
AUDIO :DSS
SLEEP :90 min
MONO/ST:STEREO
OSD INFO:ENABLE
MULTI:ON MSPKR:OFF
VOL :VARI VOL :VARI
LEVEL: - 20dB LEVEL: - 90dB
VIDEO:DVD AUDIO:DVD
OPERATION OF THE MULTI ROOM OUTPUTS
WITH THE REMOTE CONTROL FROM MULTI B
Room B output can be operated from a room where the unit (SR7002 or SR8002) is not installed. This requires a separately sold IR receiver. (For connections, see page 37.)
Note:
The SR7002 does not use MULTIROOM B.
CHANGE THE MULTI ROOM CONTROL COMMANDS
(RC101) FOR MULTIROOM B
Change the control commands for each zone.
2.
1.
1. Press SET button and ZONE button until the SEND indicator blinks twice.
Then backlight flashes.
2. Press B zone button.
When the procedure is successful, the SEND indicator will blink twice.
These buttons change a special code of each zone.
POWER ON/OFF
SOURCE
VOL +/–
MUTE
Tuner mode operation remote code (Refer to page 26)
Notes for the Multi Room System | ENGLISH | |
• If the Tuner (FM or AM) is active in the main room, | ||
| ||
you can not control any function of the tuner.In this |
| |
case, You must listen to the same station as the main |
| |
room. |
| |
|
|
OPERATION OF THE MULTI SPEAKER
OUTPUTS WITH THE REMOTE CONTROL
To switch to MULTI SPEAKER SYSTEM (A or B) control, perform the following operations with the RC101 set to MULTI ROOM A or MULTI ROOM B.
1. 3.
2. 1.
1. Press SET button and POWER ON button until the SEND indicator blinks twice.
Then backlight flashes.
2. Press the DVD button.
Note
Press the TV button at this time to return to the MULTI ROOM settings.
3. Press ENTER button once to lock in the code.
When the procedure is successful, the SEND indicator will blink twice.
79