SETTING THE MACRO TIMER
ENGLISH | Setting the macro timer enables the macro program | ||
to automatically turn the power for a device on or off | |||
or perform other operations. |
| ||
In the settings, you can select to execute the macro | |||
timer everyday or only once. |
| ||
|
| ||
| Be sure to set the clock to the correct time before | ||
| using the timer. The macro timer can only be set for | ||
| one program a day. |
| |
| This example shows how to use the timer only once | ||
| at 20:35 to execute a macro programmed to | ||
| 2 | 3 | 4 |
EXECUTING THE MACRO TIMER
The macro program starts when the time that was set is reached. The TIMER indicator lights up whenever the macro timer is activated.
Note:
•To execute the macro timer, place the remote controller facing the infrared sensor of the device to be operated. If the remote controller is not in a suitable position, it may not operate the device properly.
CLONE MODE
1. Place the receiver sensor of the receiving remote control (top) so that it is facing the transmitter of the transmitting remote control (top) at a distance of about 5 cm (2 inches).
2. Hold down the M button of the transmitting remote controller for three seconds or more.
The menu is displayed.
3. Press the > button to display the fourth page CLONE menu.
4. Press the D3 (TX) direct button. The transmitting side is now ready.
5. Hold down the M button of the receiving remote controller for three seconds or more.
COPYING BY SOURCE
The 12 sources can be copied on a source by source basis. You can select from up to 12 source types.
<Receiving remote controller>
6 |
| 7 |
| 8 |
|
| ||
LEARN |
|
| LEARN |
|
| LEARN |
|
|
NAME |
|
| NAME |
|
| NAME |
|
|
MACRO |
|
| MACRO |
|
| MACRO |
|
|
USE | PAGE 1 2 3 4 |
| USE | PAGE 1 2 3 4 |
| USE | PAGE | 1 2 3 4 |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
1. Place the receiver sensor of the receiving
LEARN
NAME
MACRO
USE
LEARN
NAME
MACRO
USE
LEARN
NAME
MACRO
USEPAGE 1 2 3 4
6
LEARN
NAME
MACRO
USEPAGE 1 2 3 4
LEARN
NAME
MACRO
USEPAGE 1 2 3 4
CREATING COPIES USING CLONE MODE
All of the codes programmed to the RC8001SR remote controller can be copied to another RC8001SR using a few simple operations.
•The remote controller can copy the entire contents or the contents for specific source buttons.
•When copying the entire contents, all programmed codes, modified names, programmed macros, and signal transmission intervals are copied.
When copying the contents for source buttons, the programmed codes and modified names are copied.
Note:
•The clone function can only be used for copying when using the same model (RC8001SR) for both the transmitting and receiving remote controller.
COPYING ENTIRE CONTENTS
<Transmitting remote controller> |
|
|
|
|
| ||||||
3 |
| 4 |
|
| 9 |
|
|
|
| ||
| LEARN |
|
| LEARN |
|
| LEARN |
|
|
|
|
| NAME |
|
| NAME |
|
| NAME |
|
|
|
|
| MACRO |
|
| MACRO |
|
| MACRO |
|
|
|
|
| USE | PAGE 1 2 3 4 |
| USE | PAGE 1 2 3 4 |
| USE | PAGE 1 | 2 | 3 | 4 |
|
|
|
|
|
|
|
|
|
| ||
<Receiving remote controller> |
|
|
|
|
| ||||||
5 |
| 6 |
|
| 9 |
|
|
|
| ||
| LEARN |
|
| LEARN |
|
| LEARN |
|
|
|
|
| NAME |
|
| NAME |
|
| NAME |
|
|
|
|
| MACRO |
|
| MACRO |
|
| MACRO |
|
|
|
|
| USE | PAGE 1 2 3 4 |
| USE | PAGE 1 2 3 4 |
| USE | PAGE 1 | 2 | 3 | 4 |
|
|
|
|
|
|
|
|
|
|
|
|
The menu is displayed.
6. Press the > button to display the fourth page CLONE menu.
7. Press the D1 (RX) direct button. The receiving side is now ready.
8. Press the OK cursor button on the receiving remote controller.
9. Press the OK cursor button on the transmitting remote controller.
When copying is started, the bar indicators on both LCDs start to move from the left to the right.
•When the copying operation is completed, TX OK is displayed on the LCD of the transmitting remote controller, and RX OK is displayed on the LCD of the receiving remote controller.
•Do not touch either of the remote controllers during the copying operation. Doing so could cause copying to fail.
•If the copying fails in the middle of the copying process, RX ERROR is displayed on the receiving remote controller. Check and perform steps 1 to 7 again.
•Copying takes about three minutes to complete when the transmitting remote controller has been programmed to 100% capacity.
10.Once copying is completed, press the M button on both remote controllers.
remote control (top) so that it is facing the transmitter of the transmitting remote control (top) at a distance of about 5 cm (2 inches).
2. Hold down the M button of the transmitting remote controller for three seconds or more.
The menu is displayed.
3. Press the > button to display the fourth page CLONE menu.
4. Press the D3 (TX) direct button.
The transmitting side is now ready.
5. Hold down the M button of the receiving remote controller for three seconds or more.
6. Press the > button to display the fourth page CLONE menu.
7. Press the D2
8. Press the source button to be copied.
The receiving side is now ready.
The name of the source which was pressed is displayed on the LCD.
•Each time the source button is pressed, the name is displayed on the LCD.
9.Press the OK cursor button on the receiving remote controller.
10. Press the OK cursor button on the transmitting remote controller.
When copying is started, the bar indicators on both LCDs start to move from the left to the right.
•When the copying operation is completed, TX OK is displayed on the LCD of the transmitting remote controller, and RX OK is displayed on the LCD of the receiving remote controller.
•Do not touch either of the remote controllers during the copying operation. Doing so could cause copying to fail.
•If the copying fails in the middle of the copying process, ERROR is displayed on the remote controller.
Check and perform steps 1 to 7 again.
22