Operating Auxiliary Equipment | Miller Electric Renegade 180

. Complete Parts List available at www. MillerWelds.com

SECTION 7 − OPERATING AUXILIARY EQUIPMENT

7-1. Generator Power Panel Receptacles



1				2

4

3

If unit does not have GFCI recep- tacles, use GFCI-protected exten- sion cord.

.Generator power decreases as weld current increases.

1 240 V AC Receptacle RC1

RC1 supplies 60 Hz single-phase power at weld/power speed. Maximum output is 5 kVA/kW (peak) or 4.5 kVA/kW (continu- ous).

2120 V 20 A AC Duplex Receptacle RC2

3120 V 20 A AC Duplex Receptacle RC3

RC2 and RC3 supply 60 Hz single-phase power at weld/power speed. Maximum output from RC2 or RC3 is 2.4 kVA/kW.

NOTICE − Do not parallel the two 120 VAC duplex receptacles.

4 Supplementary Protector CB1

CB1 protects the receptacles from over- load. If CB1 opens, the receptacles do not work. Move switch to the On position to re- set.

229 573-A

.If supplementary protector continues

to open, contact Factory Authorized Service Agent.

Combined output of all receptacles limited to 4.5 kVA/kW continuous rating of the generator (See Section 13 − Generator Power Guidelines).

EXAMPLE: If 10 A is drawn from each 120 volt duplex receptacle, only 8 A is available from the 240 V receptacle.

2 x (120 V x 10 A) + (240 V x 8 A) = 4.5 kVA/ KW.

OM-228 042 Page 30

Image 34

Miller Electric Renegade 180 manual Operating Auxiliary Equipment, Generator Power Panel Receptacles

Contents

Description OM-228 042BProcesses File Engine Drive From Miller to You Table of Contents − Maintenance 10-1 Electric Shock can kill Symbol UsageArc Welding Hazards HOT Parts can cause severe burns ARC Rays can burn eyes and skin Fumes and Gases can be hazardousBuildup of GAS can injure or kill Welding can cause fire or explosion Engine Hazards Compressed Air Hazards Fire or Explosion hazard Welding Wire can cause injuryHOT Parts can cause burns and injury Falling Unit can cause injury EMF Information Principal Safety StandardsCalifornia Proposition 65 Warnings Radiation can cause interference UN Choc Électrique peut tuer Signification des symboles− Consignes DE Sécurité − Lire Avant Utilisation Indique des instructions spécifiques LES Fumées ET LES GAZ peuvent être dangereux DES Pièces Chaudes peuvent provoquer des brûlures gravesLE Soudage peut provoquer un in cendie ou une explosion ’EXPLOSION DE LA Batterie peu LE Bruit peut affecter l’ouïeDES Organes Mobiles peuvent pro voquer des blessures ’AIR Comprimé peut provoquer des blessures LA Chaleur DU Moteur peut pro- voquer un incendieRisque D’INCENDIE OU D’EXPLO- Sion LES Fils DE Soudage peuvent provoquer des blessures LE Surchauffement peut endom- mager le moteur électriqueDES Organes Mobiles peuvent provoquer des blessures ’EMPLOI Excessif peut Principales normes de sécurité Proposition californienne 65 AvertissementsInformation EMF Weld, Power, And Engine Specifications − SpecificationsSymbol Definitions − Definitions Optional Lifting Eye Weight Rating Gun SpecificationsDimensions, Weights, And Operating Angles Volt-Ampere Curves Power Source Duty Cycle Fuel Consumption Volts Generator Power CurveGun Duty Cycle And Overheating AC Amperes Movement − InstallationInstalling Welding Generator Airflow Clearance Grounding Generator When Supplying Building Systems Use ground device as stated in electrical codes + − Connecting The Battery Electric Start Models OnlyEngine Prestart Checks Oil Installing Welding Gun Work Cable Routing Inside Unit Weld Process/Polarity Table Changing Weld Polarity Shown with optional cylinder rack Connecting Single−Phase, 230 Volt AC Utility Input PowerThis unit can provide weld out When a slight force is needed to turn spool, tension is set Electrical Service GuideInstalling Wire Spool And Adjusting Hub Tension Adapter Weld Position Threading The Welding Gun Stamped Stamped .030/.035 Tighten Pressure Indicator ScaleTools Needed 150 mm 030/.035 Groove Wood − Operating the Welding Generator Controls See Section To Start Description Of Controls See SectionTo Stop Weld Parameter Chart Stainless Steel And 100% CO2 Weld Parameters 20 ga 18 ga 16 ga 14 ga Generator power decreases as weld current increases Generator Power Panel Receptacles− Operating Auxiliary Equipment − Maintenance Power Source Routine Maintenance Drive Motor Protection Gun Routine MaintenanceWelding Power Source Overload Protection Tip Saver/Short Circuit Protection Turn Off power before replacing contact tip Changing Drive Roll Or Wire Inlet GuideReplacing Gun Contact Tip Turn off welding power source/wire feeder Maintaining Gun Replacing Switch And/Or Head Tube Tools Needed 19 mm Do not wash paper element or clean with compressed air Servicing Air CleanerPrecleaner Paper Element Standard Model Shown Stop engine Adjusting Engine Speed Stop engine. Close fuel valve Generator Power − TroubleshootingTroubleshooting Welding Engine Wire FeederDoes not run Recommended Spare Parts − Parts ListRecommended Spare Parts − Electrical Diagrams OM-217 454 Typical MIG Process Connections Regulator Flowmeter Wire Feeder Power Source Shielding Gas− MIG Welding Gmaw Guidelines Gun Work Clamp Workpiece Wire Suggested Wire Speed Typical MIG Process Control SettingsThese settings are guidelines only. Material Material thickness determines weld parameters Tioned correctly on seam Nozzle, and tip of wire is posiHolding And Positioning Welding Gun Groove Welds Electrode Extensions Stickout Conditions That Affect Weld Bead ShapeGun Angles And Weld Bead Profiles Fillet Weld Electrode Extension Stickout Good Weld Bead Characteristics Poor Weld Bead CharacteristicsGun Movement During Welding Troubleshooting − Porosity Troubleshooting − Excessive SpatterPossible Causes Corrective Actions 12-11 Troubleshooting − Lack Of Penetration Troubleshooting − Excessive PenetrationTroubleshooting − Incomplete Fusion Troubleshooting − Waviness Of Bead 12-13 Troubleshooting − Burn-ThroughTroubleshooting − Distortion Application Common MIG Shielding GasesFlat & Horizontal1 Fillet Selecting Equipment − Generator Power GuidelinesGrounding Generator To Truck Or Trailer Frame Grounding When Supplying Building Systems How Much Power Does Equipment Require? Industrial Motors Rating Starting Watts Running Watts Approximate Power Requirements For Industrial MotorsApproximate Power Requirements For Farm/Home Equipment Farm/Home Equipment Rating Starting Watts Running Watts Approximate Power Requirements For Contractor Equipment Contractor Rating Starting Watts Running Watts Single-Phase Induction Motor Starting Requirements Power Required To Start MotorHow Much Power Can Generator Supply? KVA/HP x HP x 1000 / Volts = Starting Amperage Typical Connections To Supply Standby Power Current Load Watts Amperes Selecting Extension Cord Use Shortest Cord PossibleCord Lengths for 120 Volt Loads Cord Lengths for 240 Volt Loads SOCKET/WRENCH Selection Table Standard Metric Your distributor also gives ServiceSupport For assistance in filing or settling claims, contact To locate a Distributor or Service Agency visitMiller Electric Mfg. Co Your distributor and/or equipment manufacturer’s