Connecting External Devices and NetCommand® Setup

NetCommand is able to control many current audio and video devices by sending remote control signals from the TV to each device through IR emitters. Additionally, it is also able to learn the remote control signals used by most audio video devices not already in the TV’s memory. NetCommand can automatically switch the TV and compatible or learned Audio/Video (A/V) Receivers to the correct input used with each device. It is important that the inputs on the TV and A/V receiver back panels match the NetCommand setup that is displayed on screen.

To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand Setup procedure in this chapter, which details the type and brands of devices you are connecting to the TV. The NetCommand Setup also assigns preset TV and A/V receiver inputs for each device. You should connect each device to the TV input (both audio and video) and to the A/V receiver (audio) as shown in the figure below. If you connect devices to inputs other than the ones shown as presets, you must change the NetCommand setup accordingly. See the Edit NetCommand information starting on page 47.

Device to be

video and stereo connected audio cables

*3&NJUUFST

stereo and/or digital audio cables

TV

stereo and/or digital audio cables

AV Receiver

The following charts show which preset inputs you should use on the TV and A/V receiver. Chart 1 shows the default TV inputs existing in NetCommand.

Chart 2 shows the A/V receiver inputs used by A/V receiver models already known by NetCommand.

 

Chart 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NetCommand Default Device Audio and Video Outputs to TV Inputs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cable for CableCARD™ Service

 

ANT-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Antenna/Cable (digital/analog)

 

 

ANT-1 if primary viewing source,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ANT-2 if secondary viewing source

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cable box

 

 

 

 

 

 

COMPONENT-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VCR

 

 

 

 

 

 

Input-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Satellite Receiver (SAT)

 

 

Input-2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Camcorder

 

 

 

 

 

 

Input-3 (on front panel)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DVD Player

 

 

 

 

 

 

COMPONENT-2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PC

 

 

 

 

 

 

HDMI-2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chart 2

Mitsubishi 1

Mitsubishi 2

 

Bose

 

Denon

Integra

Kenwood

Marantz

 

Pioneer 1

Pioneer 2

 

Rotel

Sony

Yamaha 1

Yamaha 2

 

 

Model

Model

 

Model

 

Model

Model

Model

Model

 

Model

Model

 

Model

Model

Model

Model

 

 

 

 

 

 

 

 

 

M-VR800 &

M-VR900 &

 

Lifestyle ®28

AVR-2700

DTR-9.1

VR-2080

SR8200

 

VSX-D557

VSX-9TX

 

RSX-1065

STR-DE825

RV-X2095

RX-V2200

 

 

M-VR1000

M-VR700

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Device Audio Output

to

AV Receiver Inputs by Name

 

 

 

 

 

 

 

 

 

 

 

 

VCR

 

VCR 1

VCR

 

VCR

 

VCR-1

Video 1

Video 1

VCR1

 

VCR/Tape

VCR 1/DVR

 

Video 2

Video 1

VCR 1

VCR 1

 

Satellite Receiver

 

Aux

Cable/DBS

 

AUX

 

CD

Video 3

Video 3

DSS

 

CD

SAT

 

Video 4

TV/DBS

TV/DBS

D-TV/LD

 

DVD Player

 

DVD

DVD

 

(built-in)

 

DVDVDP

DVD

Video 4

DVD

 

LD/SAT

DVD/LD

 

Video 5

TAPE/MD

CD

DVD

 

TV Monitor Output

 

TV

TV

 

TV

 

TV/DBS

Video 4

Video 4

TV

 

DVD/TV

TV

 

Video 1

DVD/LD

DVD/LD

CBL/SAT

 

(& Digital Audio)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

After using NetCommand Setup, you may go to the NetCommand menu at any time to change the inputs you used for connecting each device, custom name devices, add devices not included in the presets above or delete devices no longer used. See Edit NetCommand. See Helpful Hints at the end of this chapter for additional information on device setup.

22

Chapter 2. Connecting

Page 22
Image 22
Mitsubishi Electronics WD-52627, WD-62627 manual Connecting External Devices and NetCommand Setup