Mitsubishi Electronics WD-52627 manual Hdtv Cable Box or Satellite Receiver with Component Video

Connecting an HDTV Cable Box or Satellite Receiver with Component Video

Connecting an HDMI Device

HDTV Cable Box or Satellite Receiver with Component Video

Figure 11

A coaxial splitter, RCA component video cables, and audio cables are required. These are not included with the TV.

1.Connect the outside antenna, cable, or satellite to ANT or SATELLITE IN on the cable box or satellite receiver. See your device’s owner’s guide for instructions and cable compatibility.

2.Connect the incoming terrestrial antenna or cable (not satellite) to ANT-1 on the TV back panel (a coaxial splitter, available at most electronic supply stores, may be required to complete this installation).

	57 #BDL 1BOFM 4FDUJPO
		1	2	
			COMPONENT
	INPUT		YPbPr (480i/480p/720p/1080i)
	1	2			Y		INPUT	OUTPUT
							DVI
								AUDIO	RECORD
	S-VIDEO					Analog Audio		OUTPUT	OUTPUT
					Pb	1	2
									VIDEO
				8IJUF
									LEFT/
	VIDEO				Pr				AUDIO-
					AUDIO-				(MONO)
	AUDIO-
	LEFT/				LEFT/
	(MONO)				(MONO)				AUDIO-
									RIGHT
	AUDIO-				AUDIO-
	RIGHT				RIGHT
				3FE		MONITORLINK™/HDMI		PC - 60Hz
						VIDEO 480i/480p/720p/1080i		VGA, W-VGA,
						AUDIO PCM LINEAR		SVGA, W-SVGA,
						1	2	XGA, 1280 X 720
	',INK¸
		IR EMITTER
		Net Command¸

	DTV/CABLE/
*ODPNJOH	VHF/UHF
				DIGITAL					IEEE1394
				AUDIO	CableCARD™ USE WITH ANT 1 CARD TOP
"OUFOOB PS		ANT 1 / MAIN	ANT 2 / AUX	OUTPUT
									INPUT/
									OUTPUT
$BCMF

HDTV Receiver to TV Back panel

•Y to Y

•Pr to Pr

•Pb to Pb

4.Connect L (left) and R (right) audio cables from the DTV receiver to Component-1 AUDIO on the TV back panel.

5.If you are using a satellite receiver, you must change the input through NetCommand. Open the NetCommand Connection for [device] screen (see page 49) to make the change.

Note: To receive the benefits of a digital A/V receiver, connect your cable box or satellite receiver’s digital audio out to a digital input on your digital A/V receiver.

HDMI Device

Figure 12

An HDMI-to-HDMI cable is required. This is not included with the TV. It may be available at your local electronics retailer

Connect an HDMI cable from the TV back panel to the HDMI device output. HDMI devices provide video and audio through this cable, so no other connection is required. You can connect two HDMI devices to the TV back panel through the HDMI connections.

	VIDEO 480i/480p/720p/1080i		VGA, W-VGA,
	AUDIO PCM LINEAR		SVGA, W-SVGA,
	1	2	XGA, 1280 X 720
DIGITAL
AUDIO	CableCARD™ USE WITH ANT 1 CARD TOP
OUTPUT			IEEE 1394
			INPUT/



"6%*0	"6%*0	8IJUF		
-	-	7$3
:
		$0/530-		065 50 57
1C				$) 
3	3			$) 
			%*(*5"-
3'		3FE	"6%*0 065
1S
7*%&0	7*%&0
1)0/& +"$, 3&.05&		47*%&0		*/ '30. "/5

)%57
3FDFJWFS
XJUI
:1S1C
DPOOFDUJPOT



5P
BOUFOOB

 DBCMF
PS
TBUFMMJUF

$"65*0/ 3*4,
0'
&-&$53*$"-
4)0$, %0
/05
01&/

4"5&--*5&
*/

PS

OUTPUT

57
#BDL
1BOFM
%FUBJM

)%.*
%FWJDF

Figure 12. Connecting an HDMI Device

Figure 11. Connecting an External HDTV Receiver with Component Video Connections

3.Connect RCA-type cables from the YPrPb outputs on the HDTV receiver to Component-1 on the TV back panel, matching the correct connections:

Note: To use the benefits of digital surround sound from th HDMI device, connect the digital audio output of the HDMI device directly to the A/V receiver.

30 Chapter 2. Connecting