Connecting an A/V Receiver (Stereo System)
Connecting a Satellite Receiver or Other Device with S
A/V Receiver (Stereo System)
Figure 7
A digital audio cable and stereo audio cables are required. These cables are not included with the TV.
1. To connect an analog A/V receiver:
Connect a set of stereo audio cables from OUTPUT AUDIO 2 on the TV back panel to the TV AUDIO INPUT on the back of the A/V receiver. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.
2.To connect a digital A/V receiver with Dolby® Digital surround sound:
Connect one end of the digital audio cable supplied with the TV to DIGITAL AUDIO on the back of the TV. Connect the other end to the COAXIAL DIGITAL INPUT on the back of the A/V receiver.
Check the A/V receiver’s Owner’s Guide for information concerning use of the digital input and switching between digital sound and analog stereo sound from the TV.
Satellite Receiver or Other Device with S-Video
Figure 8
An
1.Connect an
2.Connect a set of audio cables from AUDIO OUT on the satellite receiver back panel to
Note: Refer to the Satellite Receiver Owner’s Guide for Dish Antenna connections
|
| "OZ47JEFP%FWJDF | ||
| 8IJUF | "6%*0065 | "6%*0*/ | 7*%&0065 |
|
| - | - | :$ |
|
|
| ||
| 3 | 3 |
| |
|
|
|
| |
3FE |
|
|
| |
|
|
|
| |
"73FDFJWFS3FBS1BOFM |
|
|
|
|
|
|
|
| |
|
| 6TFPOMZJG |
|
|
|
|
|
|
|
|
|
| |
|
| DPOOFDUJOHB |
|
|
|
|
|
|
|
|
| ||
|
| %PMCZEJHJUBM |
|
|
|
|
|
|
|
|
| ||
| "7SFDFJWFS |
|
|
|
|
| 57CBDLQBOFMTFDUJPO | ||||||
|
|
|
|
|
|
| |||||||
|
|
| 8IJUF |
|
| COMPONENT |
|
|
|
|
| ||
|
|
| INPUT | 1 | YPbPr (480i/480p/720p/1080i)2 |
|
|
|
| ||||
|
|
|
|
| 1 | 2 |
| Y |
| INPUT | OUTPUT | ||
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| DVI |
|
| ||
|
|
|
|
|
|
|
|
|
| AUDIO | RECORD | ||
|
|
|
|
|
|
|
| Analog Audio | OUTPUT | OUTPUT | |||
|
|
|
|
|
|
|
| Pb | 1 | 2 |
|
| |
|
|
|
|
|
|
|
|
|
| VIDEO | |||
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| 3FE | VIDEO |
|
|
| Pr |
|
|
| AUDIO- | |
|
|
| AUDIO- |
|
|
| AUDIO- |
|
|
| LEFT/ | ||
|
|
|
|
|
|
|
|
|
|
|
| (MONO) | |
|
|
|
| LEFT/ |
|
|
| LEFT/ |
|
|
|
| |
|
|
|
| (MONO) |
|
|
| (MONO) |
|
|
| AUDIO- | |
|
|
|
|
|
|
|
|
|
|
|
| RIGHT | |
|
|
|
| AUDIO- |
|
|
| AUDIO- |
|
|
|
| |
|
|
|
| RIGHT |
|
|
| RIGHT |
|
|
|
| |
|
|
|
|
|
|
|
|
| MONITORLINK™/HDMI | PC - 60Hz |
| ||
|
|
|
|
|
|
|
|
| VIDEO 480i/480p/720p/1080i | VGA, | |||
|
|
|
|
|
|
|
|
| AUDIO PCM LINEAR | SVGA, | |||
|
|
|
|
|
|
|
|
| 1 | 2 | XGA, 1280 X 720 | ||
|
|
|
| ',INK¸ |
|
|
|
|
|
|
| ||
|
|
|
|
|
| IR EMITTER |
|
|
|
|
|
| |
|
|
|
|
|
| Net Command¸ |
|
|
|
|
|
| |
57#BDL1BOFM |
|
|
|
|
|
|
|
|
|
|
|
| |
4FDUJPO |
|
|
| DTV/CABLE/ |
|
|
|
|
|
|
| ||
|
|
|
| VHF/UHF |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| DIGITAL |
|
|
|
|
| |
|
|
|
|
|
| ANT 1 / MAIN | AUDIO | CableCARD™ USE WITH ANT 1 CARD TOP |
|
|
| ||
Figure 7. Connecting an A/V receiver |
|
|
| ANT 2 / AUX OUTPUT |
|
|
| ||||||
|
|
|
|
|
|
|
|
| IEEE 1394 | ||||
|
|
|
|
|
|
|
|
|
|
|
| INPUT/ | |
|
|
|
|
|
|
|
|
|
|
|
| OUTPUT | |
Note: On rare occasions, an HDMI signal may be copy- | Figure 8. Connecting a Satellite Receiver with | ||||||||||||
restricted and cannot be output from the TV as a digital | |||||||||||||
|
|
|
|
|
|
|
|
|
| ||||
signal. To hear these |
|
|
|
|
|
|
|
|
|
| |||
A/V receiver, use connections for analog A/V receivers. | Note: NetCommand® will assume you connected | ||||||||||||
MP3 audio from memory cards cannot be connected | your Satellite Receiver to | ||||||||||||
to digital audio. To listen to MP3 playback from the TV | Satellite Receiver or use any other inputs for your | |
Satellite Receiver, this change must match in the | ||
MediaCommand memory card player through your A/V | ||
NetCommand system. See Editing NetCommand | ||
receiver, use the connections for an analog A/V receiver. | ||
Setup in Chapter 3 for more information. | ||
|
28 | Chapter 2. Connecting |
