Mitsubishi Electronics WD-52627 manual VCR to an Antenna or Wall Outlet Cable Audio & Video, $Bcmf

Connecting a VCR to an Antenna or Wall Outlet Cable Connecting VCR Audio and Video to the TV

VCR to an Antenna or Wall Outlet Cable (Audio & Video)

Figure 5

A two-way RF splitter, 3 coaxial cables, right and left audio cables and an S-Video or Video cable are required. These are not included with the TV.

1.Connect the incoming cable or Antenna to IN on the RF splitter.

2.Connect one coaxial cable from OUT on the RF splitter to ANTENNA IN on the VCR back panel.

3.Connect one coaxial cable from OUT on the RF splitter to ANT-1 MAIN on the TV back panel. This connection also allows you to use the TV Guide On Screen® feature.

4.To use the TV speakers with the VCR, connect a

set of audio cables from AUDIO OUT on the VCR back panel to INPUT-1 AUDIO-LEFT (MONO) and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel. If your VCR is mono (non-stereo), connect only the white (left) cable.

5.Connect either an S-Video or Video cable from VIDEO OUT on the VCR back panel to INPUT-1 VIDEO on the TV back panel. Only one type of video cable should be connected. S-Video is recommended, if available.

6.For NetCommand® controlled recordings (including TV Guide On Screen), connect a set of audio cables from AUDIO IN on the VCR back panel to RECORD OUTPUT/AUDIO-LEFT and AUDIO-RIGHT on the TV back panel. The red cable connects to the R (right) channel and the white cable connects to the L (left) channel.

7.Complete the NetCommand controlled recordings connections by connecting a Video cable from VIDEO IN on the VCR back panel to RECORD OUTPUT/VIDEO on the TV back panel.





*55&3

065

-

*ODPNJOH

*/ 41 8": 580

065



$BCMF

3' 4QMJUUFS





*G ZPVS 7$3 IBT B

WJEFP DIBOOFM PS 3'

0/0'' TXJUDI TFU JU

)46



UP 0''

7$3 CBDL QBOFM







INPUT

COMPONENT

YPbPr (480i/480p/720p/1080i)



1

2



1

2

Y

INPUT

OUTPUT

DVI

AUDIO

RECORD

"UUBDI POMZ POF DBCMF UZQF

S-VIDEO

Analog Audio

OUTPUT

OUTPUT

Pb

1

2

VIDEO

4WJEFP SFDPNNFOEFE JG

VIDEO

Pr

AUDIO-



LEFT/

AUDIO-

(MONO)

BWBJMBCMF

AUDIO-

LEFT/

LEFT/

(MONO)

(MONO)

AUDIO-

RIGHT

AUDIO-

AUDIO-

RIGHT

RIGHT

MONITORLINK™/HDMI

PC - 60Hz



VIDEO 480i/480p/720p/1080i

VGA, W-VGA,

AUDIO PCM LINEAR

SVGA, W-SVGA,

1

2

XGA, 1280 X 720

',INK¸

IR EMITTER

Net Command¸



DTV/CABLE/

VHF/UHF

DIGITAL

466"ACKC

ANT 1 / MAIN

AUDIO

CableCARD™ USE WITH ANT 1 CARD TOP

ANT 2 / AUX OUTPUT

IEEE 1394

INPUT/

OUTPUT

0ANEL

Figure 5. Connecting a VCR to an Antenna or Wall Outlet Cable

26

Chapter 2. Connecting

Note:

NetCommand® will assume your VCR is connected to inputs as shown on this page. If you use any other inputs for your VCR or add a second VCR, this change must match in the NetCommand system. See Edit NetCommand... in Chapter 3 for more information.