Status Light Messages | Mitsubishi Electronics XD20A specification

W h e n t h e S T A T U S i n d i c a t o r l i g h t s o r f l a s h e s

STATUS indicator

POWER STATUS

POWER SOURCE AUTO

Status Light Messages

Condition	Status

OFF	Normal

On Continually	The lamp usage has exceeded 1000 hours of operation and should be replaced.

Flashing Very Rapidly (On and off	•	The lamp cover is not correctly attached. Replace it correctly.
in a cycle of 1 sec.)

Flashing Rapidly	•	The temperature protector has been triggered. If the room temperature is high,
Flashing Rapidly		move the unit to a cool location. If the temperature within the unit is high, check the
(On and off in a cycle of 4 sec.)
(On and off in a cycle of 4 sec.)		cooling fan ventilation slots and the ventilation slots on the bottom of the unit. If

		any of the slots are blocked, remove whatever is blocking them.
	•	The temperature protector has been triggered. If you try to turn on the unit immedi-
		ately after turning off, sometimes the power does not come on. If this happens, wait
		at least one minute, then turn on the unit again.
	•	The lamp lighting voltage error detection protector has been triggered. Wait at
		least one minute before turning on the unit again. If this does not solve the problem,
		please contact your dealer.

Flashing Slowly (On and off in a	The cooling fan has stopped. Contact your MITSUBISHI dealer for service.
cycle of 8 sec.)

Flashing Very Slowly (On and off in	The lamp is not turned on.
a cycle of 12 sec.)	• The unit was turned on immediately after being turned off. Turn off the unit, wait at
		least one minute, then turn on the unit again.
	•	The lamp is dead. Replace the lamp cartridge. (See page 33.)

E – 32

Image 32

Mitsubishi Electronics XD20A user manual Status Light Messages, Status indicator

Contents

Data Projector Precautions Important SafeguardsInstallation Power Supply B l e o f c o n t e n t s Power cable mains lead 1.8 m/5.9 ft A t u r e sE c k i n g t h e P p l i e d a c c e s s o r i e s RGB cable Audio cable 3.3 ft Remote control effective range E p a r i n g t h e M o t e c o n t r o lInserting the batteries Quick Start Guide Bottom R t s a n d c o n t r o l sTop, front and side panel view Audio jack 10, 11, 12 RGB/YCbCr connector 11 Mouse connectorRear and side panel view Built-in Security Slot Mute button Enter button 17 Infrared transmitterAuto button Freeze button Installation Installation Guidelines normal installationScreen height Screen size N n e c t i n g v i d e o e q u i p m e n t Connection to the Video jack of the unitRear panel jacks of this device Connection to the S-VIDEO jack of the unit Connection to the RGB/YCbCr connector N n e c t i n g a P C o r M a c i n t o s h Changing the computer’s video resolutions Windows 98/WindowsWindows Macintosh Connect the power cord Adjust the position and height of the unitI n g t h e u n i t Turn on the connected source computer, VCR, DVD player, etc Case of RGB input, adjust the video of the connected PC After using the unit I n g t h e u n i t N t i n u e d IBM PS/2 Mouse Port Connection Remote control mouse functionsUSB Port Connection Automatic Screen Adjustment Adjusting the VolumeKeystone Adjustment Freezing animated images To move to the desired portion of the enlarged picture Enlarging the pictureScreen Reduction Press the desired portion of the cursor key N u S t r u c t u r e Common menu Normal menu RGB input Advanced menu Press the cursor / keys to adjust the sharpness J u s t i n g t h e p i c t u r e e l e m e n t sTo select other menu names To close the menu Timing Chart If no images appear during setting Adjusting Clock Frequency and PhaseAdjusting the position of the image Resetting Resetting the time the hours of lamp usageS e t t i n g S e t t i n g t h e L a m p H o u r s o f U s a g e Setting the Cinema Mode Adjusting Color BalanceT t i n g N a r r o w I m a g e s a d v a n c e d M e n u Selecting the Color System Setting Filter Setting the RGB/YCbCr connectorSetting the Display Frame Setting the partial display position I t i a l S e t t i n g sAudio Muting Selecting the Background Selecting a Projection Type Auto Source SettingsUsing the Power Saving Function T t i n g t h e M e n u Troubleshooting Status indicator Status Light Messages Lamp cartridge replacement procedure P l a c i n g t h e l a m pR t r i d g e Step Specification s Sub Pin AssignmentsOptical Electrical Dimensions 230 mm/9.0″Mm/7.0″ 177