4.Set the position and expansion ratio (“1.8.2 H.DISPLAY POS, V.DISPLAY POS” on page66) again to fit a configuration in reference to the following setting sample in left side. Check the
displaying to be as the example in right side.
Image signal
H=1/2 | H=2/2 |
V=1/2 | V=1/2 |
|
|
H=1/2 | H=2/2 |
V=2/2 | V=2/2 |
A 
5.Set SCREEN MODE (chapter 1.8.6, on page 67) as needed.
6.Save the display memory (chapter 1.8.7, on page 68) of each screen in a different memory number from a previous saving.
7.Check the image linkage between screens. If it is insufficient, you can tweak by OFFSET menu (chapter 1.5.1.7, on page 38). Be careful if you adjust it by the display memory setting, the linkage condition may change when you display other images.
You can also display different input images in the same time.
It is an example that an analog signal A is input to panel 1 (upper left) and a video (COMPOSITE)
signal V is input to panel 2 (upper right). Each screen is connected with daisy chain. |
|
|
|
|
|
|
| |||||||
[Procedure] | Image signal 1 |
| Image signal 2 | |||||||||||
8. | Select COMPOSITE port in the panel 2 according to “1.7.1 |
| ||||||||||||
| Input port selecting” on page 57. | (Analog input) |
| (Video input) | ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
9. | Adjust the input memory setting in the panel 2 as needed. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
10. | Save the input memory in a different memory number from a |
|
|
|
|
|
|
| V |
|
|
| ||
| previous saving. |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
11. | Set the display memory in the panel 2 as below. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| A |
|
|
| |||||||
| INPUT MEMORY: the input memory for the video input set in |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
| |||||||
| the step 10. |
|
|
|
|
|
|
| ||||||
| H.DISPLAY POS.: 1/1 |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| V.DISPLAY POS.: 1/1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| DIGITAL OUT: the input memory for the digital input set in the step 3. |
|
|
|
|
|
|
| ||||||
12. | Make certain to display the video signal V on the panel 2 as described above. |
|
|
|
|
|
|
| ||||||
13. | Save the display memory in a different memory number from a | Image signal 1 |
| Image signal 2 | ||||||||||
| previous saving. |
| ||||||||||||
| (Analog input) |
| (Video input) | |||||||||||
You can switch these image displays. |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
[Procedure] |
|
|
|
|
|
|
|
|
|
|
|
|
| |
14. | Regarding the panel 2 as a first cube, follow the same procedure |
|
|
|
|
|
|
|
|
|
|
|
|
|
| as step 2 to 7 to display as shown in the right figure. |
|
|
|
|
|
|
|
|
|
|
|
|
|
15. |
|
|
|
| V |
|
|
| ||||||
Call display memories (set in the step 3, 6 13 or 15) to switch the |
|
|
|
|
|
|
| |||||||
| display depending on cases. |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PH50, XL50, XL21 series
70
