Manuals / Mitsubishi Electronics / Computer Equipment / Projector

Mitsubishi Electronics Motorized adjustment tool, S-AXL50E specification, Applicable product

Models: XL21 XL50

1 120

Download 120 pages 23.33 Kb

Page 96

3.8. Motorized adjustment tool, S-AXL50E specification

The detail adjustment procedure is described in the chapter 1.4.3.2.2, on page 29.

3.8.1.Applicable product

This tool can be used for the following models.

•All PH50 and XL50 series

•VS-50XLF20U, VS-67XLW20U, VS-50XL21U and VS-67XL21U

•VS-67XL20U (applied from serial number 0001176)

•VS-50XLW20U (applied from serial number 0001121)

3.8.2.Outline drawing

Upper unit

Lower unit

[Unit: mm]

3.8.3.	Accessory
1.	Unit-connecting cable (shorter)	3 pieces (two cables are spares.)

2. Cube-connecting cable (longer)

3 pieces (two cables are spares.)

3. Spare latch

2 pieces (consisting of grommets and plungers)

Grommet

Plunger

PH50, XL50, XL21 series Set-up and Installation Manual

96

Image 96

Mitsubishi Electronics XL21 Motorized adjustment tool, S-AXL50E specification, Applicable product, Outline drawing

Contents

Set-up and Installation Manual Table of Contents REV 118 Set-up and installation Overview FlowchartProduct lineup Cube installation Safety precautionPreparation Input board installation optional Unlocking for XL21 Color wheel unlockingLamp cushion removing for Changer Cube stacking for Rear Assembling the base stands and cubes PH50Screen gap adjustment Fixing to the wall and floor Cube stacking for Front Tape peeling off forScreen detaching Ventilation For 67 , 50 ChangerFor 50 Single External AC fan attaching occasional Assembling base stands and cubes As needed, you can adjust the screen gaps Adjustment Screen open/close for Front Screen openingScreen closing Connecting Control signal connectionImage signal connection Case of daisy chainFor other than daisy chain Internal cabling for FrontInitial set up Menu operation Control button listOperation mode Basic menu operation Remote IDDipswitch setting Picture outline adjustmentDisplaying internal test pattern Axis adjustment AttachingFront Close the screen .2.7.2, on Adjustment DetachingPosition Keystone Tilt Zoom Correct the horizontal keystone distortion Mirror adjustment 50 XL21 XL50 Rear and PH50 System memory setting System set up Lamp PowerLamp Mode for XL21 This adjustment is normally unnecessary Terminate This adjustment is normally unnecessaryStart Memory Overlap for the input boardImage Flip This adjustment is normally unnecessary Baud RateSystem Sync Indication This adjustment is normally unnecessary Auto Power on Extended IDResolution for PH50 This adjustment is normally unnecessary Direction This adjustment is normally unnecessaryCable Length for PH50 and XL50 Lamp Change for ChangerColor balance adjustment Black Level This adjustment is not necessaryREV White Balance GradationTarget Color SensorImage set up Color MatrixuserADV.COL This adjustment is normally unnecessary ADV.DARK This adjustment is normally unnecessaryGamma This adjustment is normally unnecessary Dither This adjustment is normally unnecessaryWhite Boost This adjustment is normally unnecessary Input memory setting for the main input Automatic input signal scanningInput port selecting Signal adjustment 3.1. H.POSITION, V.POSITIONFine for Analog input AMP Gain for Analog inputSignal Select for XL21 Signal SelectClamp START=0, Clamp WIDTH=0. Procedure Contrast BrightnessColor Matrix ApertureInput memory saving Input memory calling/deletingInput memory setting for the input board Expansion setting4.1. H.POSITION, V.POSITION Fine for S.ANALOG inputAMP. Gain for S.ANALOG input Value is automatically set in automatic input signal ScanningClamp START=0, Clamp WIDTH=0. Procedure With VC-B20KA Brightness VCR Mode for Composite or Y/C input with VC-B20KV ASPECT-RATIOColor for Composite or Y/C input Tint for Composite or Y/C inputInput memory saving Display memory setting for the input board Input Memory2. H.DISPLAY POS, V.DISPLAY POS Screen Mode Digital OUTDisplay memory saving Display memory calling/deletingSetting as daisy chain connection for the input board Display POS /1 Regular maintenance 2.1. Lamp replacement Safety precautionsProcedure For SingleTighten the two lamp fixing screws For Changer Open the lamp cover Close the lamp cover Partition door Auto-lamp changing function for Changer Action in lamp failure burnout or explosionAction in brightness deterioration Manual lamp swap Lamp position auto calibrationLamp will Exchange Soon Condenser lens adjustment for Single Focus adjustment Cleaning Cleaning procedureScreen front surface CabinetFilter Reset Filter TimeAxis adjuster fixing For deliveryColor wheel locking for XL21 Lamp cushion inserting forFront Screen-holding arm locking for 67 FrontFunction Memories Menu treesInput memory Common itemsAdditional items When Analog or S.ANALOG is selected Additional items When S.DIGITAL is selectedDisplay memory System memory Items within parentheses are initial valuesMemory list display Test pattern list Control panelLED display LED display list Terminal functions RS-232C terminalControl terminal Available input signal list RGB signal Ycbcr Ypbpr component video signal Motorized adjustment tool, S-AXL50E specification AccessoryApplicable product Outline drawingTerminal for firmware upgrading/slide switch Terminals OutlineRotary dial Reset button Recovery procedure from errorTrouble shooting LEDAdjustment software, Wallaby 4.1. General InstallationInitial set-up System configuration setting Automatic panel ID settingManual panel ID setting Serial port settingAdjustment Serial port openingTurning on Picture mute offService tab for system memory MaintenanceAuto CSC function Optimize gain functionInstallation Misc Function Input tab for input memory Common items107 Additional items When S.DIGITAL is selected Additional items When Composite or Y/C is selectedDisplay tab for display memory Memory tab Information tabMemory copy Memory backup Cube data savingData sending to cubes Power and Mute Main windowPanel selection area Serial PortMenu bar Edit menu Read Parameter Send ParameterCopy Parameter Paste ParameterSystem Config menu By n 1x1, 2x2, 3x3 or Other Wall Config…Cube ID Setting Auto IDPort Setting Special menu Protect SettingSerial Port menu Log… OpenAbout trademarks Revision history Description Revision date