10 M2 2 Pin-Contact, 11 J753 Microphone Socket | Motorola I580

MECHANICAL PARTS REWORK AND REPAIR: Mechanical Parts Rework Procedure

9.5.10 M2 (2 Pin-Contact)

Top 330ºC - Bottom 100ºC

N-Q07

OK Industries	151/min	“J” over J753 during Removal Procedure.
Pace	6/7	“J” over J753 & “F” over M2 during Installation
		Procedure.

9.5.11 J753 (Microphone Socket)

Top 330ºC - Bottom 100ºC

N-P20

OK Industries	151/min	“F” over M2 during Removal Procedure.
Pace	6/7	“F” over M2 & “C” over J753 during Installation
		Procedure.

9.5.12 SW-all (Key/Switch)

Top 330ºC - Bottom 100ºC

N-Q07

OK Industries	151/min	“I” over nearby SW during Removal Procedure.
Pace	6/7	“I” over nearby SW & “I” over replaced SW during
		Installation Procedure.

NOTE: Use Flux Pen Indium-Indalloy NC771 ONLY (Motorola P/N 1185768C01). Use flux sparingly.

NOTE: Always protect switches from heat and Flux intrusion to avoid component malfunction.

NOTE: Keep alcohol or solvent away from switch area after rework to avoid reliability issues.Tack down a couple of leads if necessary.

68P80401P05

83

Image 98

Motorola I580 service manual 10 M2 2 Pin-Contact, 11 J753 Microphone Socket, SW-all Key/Switch

Contents

IDEN Digital Multi-Service, Data-Capable Portable I580 Manual Revisions Safety and General Information Electro Magnetic Interference Compatibility Medical Devices Accessory Safety Information Cleaning and Drying Considerations Safety and General Information Model Information Model Numbering System Model Specifications General Receiver Transmitter Contents Chapter Basic Level Test Modes and Procedures Chapter Field Level Test Modes and Procedures Appendix a Ordering Replacement Parts and Kits How This Manual Is Organized PrefaceWho Should Use This Manual Conventions Used in This Manual Related Publications Overview IDEN Digital Modulation Technology Spectrum of iDEN Quad 16QAM IDEN Voice Compression Technology RF Transmission Bursts Calling Area Coverage MOTOtalk Bluetooth Wireless SystemGlobal Positioning System GPS Section To remove a SIM card Figure SIM CardsRemoving and Inserting a SIM Card Removing a SIM Card To insert a SIM card Figure FEATURES, ICONS, and Indicators I580 Features Display Icons Main Menu Icons Status Icons Power-Up Sequence DISPLAYS, MESSAGES, and Alerts Self-Test Reset Errors Power-Down SequenceSelf-Test Errors Messages Service Messages Service Messages Alert Tones Alert Tones Alert Tones Alert Tones To set unit to vibrate for all calls Using the Optional Vibrate FunctionVibrator Settings From the main menu, select Settings 2-Way Radio Alert Type Test Equipment Preparing for Basic Level TestingReference Accessories Reference Unit Customer Care Reset ConditionBasic Level Checks and Self Tests Test Conditions Basic-Level Test Checklist Basic-Level Test ChecklistPreventive Maintenance To clean the unit takes approximately 3 minutes Shock and Pressure test time is approximately 3 minutes Mechanical and Electrical ChecksSIM Card Swap Test SIM Card Swap test time is approximately 5 minutes Lockup Test Accessory Swap TestAccessory Swap test time is approximately 5 minutes Lockup Test time is approximately 6 minutes Battery Connections test time is approximately 5 minutes Battery Connections TestTesting the GPS Receiver To test the GPS Receiver Voltage Recognition test time is approximately 4 minutes Self-Test ProceduresVoltage Recognition Test Passcode test time is approximately 5 minutes Programming Menu Settings CheckPasscode Test From the main menu, select Settings Display/Info Contrast Phone Calls Features Way Radio Options Personalize Volume FeaturesSecurity Features From the main menu, select Settings Security GPS PIN Advanced Features Call Performance Test Call Performance test time is approximately 7 minutes To enter Debug/Trace Mode Basic Level Test Modes and ProceduresEntering Debug Mode Test Modes Trace Mode Display Screens Display Screens GPS To enter Test Mode Test Mode Test ProceduresEntering Test Mode Audio Loopback Test Audio Loopback test time is approximately 3 minutes ESN and Imei Matching TestDebug Check ESN/IMEI Matching test time is approximately 6 minutes To monitor the data in the unit 68P80401P05 Technician Test Procedures Connecting the Unit to the RSS Workstation Programming the i580 Unit Codeplug Help Codeplug TroubleshootingTo access the codeplug Help topic in Windows Preparing for Field Level Testing Preparing Equipment for Testing Using RSS Connecting an iDEN Unit to the R-2660 Typical R-2660 Setup To connect the unit to the R-2660 RF Zone Fields and Values To enter Initial Registration modeOperating the R-2660 Disassembling and Reassembling the Unit Disassembly Sequence FlowchartAssembly/Disassembly Procedures Remove Remove Battery CoverInstall Remove Battery Remove SIM Card Remove Antenna Preparing for Field Level Testing Remove Antenna Remove Back Housing Remove Main Board, Keypad Remove Flip Assembly Procedure to remove flip assembly Preparing for Field Level Testing Remove Flip Assembly Install Flip Assembly Procedure to install flip assembly Preparing for Field Level Testing Install Flip Assembly Exploded View and Parts List I580 Component Parts List I580 Exploded View Field Level Test Modes and Procedures Field-Level Test Checklist Required Test Equipment Field-Level Test Checklist Done Technical Tests Pass Fail See the Strong Signal Environment section Registration/Call Test Signal Quality Error SQE Test R-2660 TX Power Test See Entering Test Mode Press Menu, Edit Bit Error Rate BER Test Pass Power-Up Test Keypad Test Audio Test Use this test to check the audio portion of the unit Reset Test Reset Reset Log Test To perform the reset log test Model Assembly MA Test Mode Test GPS Global Positioning System Receiver Test Use this test on a unit to check its GPS functionality Yes Bluetooth Test This Page intentionally left blank Mechanical Parts Rework and Repair Recommended Equipment Rework/Repair Requirements Recommended ToolsRecommended Supplies Board Preparation Components Identification Land Preparation Procedure Mechanical Parts Rework ProcedureRemoval Procedure Installation Procedure 5 J752 Audio Jack 4 J600 RF Connector6 J401 30 Pin Board-to-Flex Connector 9 M105 Battery Contact 7 J400 80 Pin Board-to Flex Connector8 M002 Simm Connector 11 J753 Microphone Socket SW-all Key/Switch10 M2 2 Pin-Contact 13 D401 through D412 LED Replacement Parts Ordering Replacement Parts and KitsCustomer Service Domestic Orders Replacement Kits Table A-1 Mid Rate Travel Chargers Bluetooth Accessories NNTN2344 NA Table A-2. Recommended Test Equipment and Tools Recommended Test Equipment and ToolsRecommended Programming Equipment Table A-3. Recommended Programming Equipment Table A-4. Recommended Software TTY @68P80401P05@