Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE Menu Updates, OFF 1. The RCLV item appears only if the, FREQ Mode

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 17

Menu Updates

Menu Updates

FREQ Mode

MORE

MORE . . .

	T/R	BAND	SQ	DSP			PWR	MODE	AGC	BW
	SMPX	LSB	ON	CLAR		-200	LOW	SSB	SLOW	2.1
	DPLX	USB	OFF	CLAR	.	-200	MED	AME	FAST	2.7
	DPLX	USB	OFF		.	.	MED	AME	FAST	2.7
					. .
	RXO				. .		HIGH	PLT	OFF	3.0
	RXO				.	.	HIGH	PLT	OFF	3.0
	TXO				.	OFF	MAX			3.3
	TXO				.	.	MAX			3.3
					. .
					. .					LSM
					.	.				LSM
				NF		+200				CW
										CW
					.
					.
					.
					.
					.
				CLIP		ON
				NB		OFF	Notes
						ON	Notes
						ON
				ATTN		OFF 1. The RCLV item appears only if the
				ATTN		ON	received signal level display is not
						OFF	permanently enabled using
							permanently enabled using
				Frequency			MENU>PROG>RAD>PRMT>RCLV.
				Frequency			2. The GPS item appears only when your
				Change			2. The GPS item appears only when your
				− − >			radio includes the GPS option.
				< − −			radio includes the GPS option.
	. . .		MORE			MORE
		RCLV	STOR	A/B			GPS

Note 1

BACK

CLR

A/B	Note 2
A=B
<− −
− −>

Figure 3. Frequency (FREQ) Menu

_________________________________________________________________________________________________	3

Image 17

Motorola MICOM-2ES/2RS/2TS ALE Menu Updates, OFF 1. The RCLV item appears only if the, permanently enabled using, Band

Contents

HF-SSBTRANSCEIVERS Support for MIL-STD-188-141B MICOM-2ES/2RS/2TSALESupplement to Owner’s Guide IMRMB008Page Phone Fax COMMERCIAL WARRANTY STANDARDCOMPUTER SOFTWARE COPYRIGHTS 1720 West Paul Dirac Drive MotorolaTallahassee 32310 FL, USA Cat. No. IMRMB008Page Warnings, Cautions and Notes General Safety PrecautionsTwo-WayRadios Installed in Vehicles or as Fixed Product Safety and RF Exposure for MobileInformation for Safe, Efficient Operation Site Control StationsFederal Communication Commission Regulations Communication Commission Regulations section When using your radio while driving, please Driver SafetyFacilities VehiclesFor Vehicles with an Air Bag Operational WarningsPotentially Explosive Atmospheres Blasting Caps and Blasting AreasPage Table of ContentsMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Figure 1. Main Menu Menu UpdatesIntroduction Figure 2. Channel CH Menu received signal level display is not Menu Updatespermanently enabled using 2. The GPS item appears only when yourPROG Menu MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideLANG ENGLISHLANG Menu UpdatesPROG Menu ENGLISHALE Addressing Method New ALE FeaturesSelective Calling Individual Station Address Address and Call TypesGroup Addresses Net AddressesSpecial Addressing Modes - Use of Wildcards Table 1. Use of “@” Stuffing Symbol ContTable 2. Use of “?” Wildcard Symbol Table 2. Use of “?” Wildcard Symbol Cont AllCall AddressesSelf Addresses AnyCallsNull Address Inlink AddressUsing the MultiNet Feature Using the Caller Stack Using ALE Functions in the Channel ModeMessages Quick CallEnabling the ALE Mode Entering the ALE ModeALE and Rx Only or Tx Only Channels ALE ProgrammingALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving an individual call Receiving Calls in ALE ModeReceiving a net call Receiving an AllCallReceiving a sounding call Receiving an AnyCallReceiving a bidirectional handshake call To answer an incoming callTo display LQA for the received call Link StateLink State Options BAND LQA F3RPL MORE, F1 RCLV MODEFREQ To replace the channelTo view the calls in the stack Using the Caller StackTo disconnect an incoming call Disconnecting CallsTo remove an address from the stack To select a net Transmitting Calls in ALE ModeSelecting the Desired Net To transmit an individual call with MultiNet OFF Calls to an Individual Station1234 To transmit an individual call with MultiNet ON LINK1234 To transmit on a specific channel 1234 Quick CallTo send a quick call To use Autodial to send a call Using AutodialTo transmit an individual call with a message Sending Messages1234 To send a message during a call link stateTo select a special call type Other Types of CallsOption CapabilitiesOption Transmitting AIICallsCapabilities See Page …To send global AllCall using the CALL function To send global AllCall using the ESC keyTo send selective AllCall LINK SL ALLCALL 11.To end the call, press ESCEND CALLING MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideTo transmit a net call Transmitting Net CallsTransmitting Group Calls LEAST To transmit a group callTo define or change a group Transmitting AnyCalls NOT PROG To transmit an AnyCallANY @@? CALLANY @@2 ANY @59To transmit a wildcard call Transmitting Wildcard CallsAT LEAST NOT PROGTo send a self-call Transmitting a Self CallBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net To manually initiate sounding SoundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode To enter the ALE Programming mode ALE ProgrammingNET RCV DescriptionNet Programming Overview Programming NetsDIR AMD DescriptionNAME MEMB CHAN GET ERAS Default ValuesSLNT LQAR Setting the Net OptionsHACK MACKDirectory Parameters AMD Message ConfigurationMLQA QCAL ALE Options ConfigurationEXAL ALRT ILNK BDLK AMD Auto Dial ParametersStoring ALE Parameters Using the New Station Address Filter