Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE manual Transmitting Calls in ALE Mode, Selecting the Desired Net

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 38

Transmitting Calls in ALE Mode

MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide

Transmitting Calls in ALE Mode

To transmit an ALE call, you must specify the destination. In general, the destination consists of a net and one or more stations (members of the specified net):

•When the MultiNet function (page 12) is disabled, the destination net is always the currently selected net (its number is displayed on the LCD while the radio is scanning). Therefore, if you do not want to select a different net, you can skip directly to the selection of the destination station(s).

•When the MultiNet function is enabled, first you must always select a net and then the destination station(s).

To expedite the transmission of an AllCall, you can send a global AllCall by pressing the P/ESC key for a few seconds.

MICOM-2 stores the last called address, so you can simply press the PTT twice in rapid sequence (double pressing) to call again that address. This also applies to AllCall, and therefore after sending AllCall for the first time, you can send it again by double pressing the PTT.

						If you want to monitor the call set up process on the speaker and
						be alerted by a beep when the link is set up, turn the monitor on,





						using the MON (F4) key.
	Note					using the MON (F4) key.
	Note

Selecting the Desired Net

➤To select a net:

1.Press MENU and select ALE (F3).

The radio displays current active net number, flashing.

2.To change the currently used net, press the

UP/DOWN keys, or enter the net number on the keypad, and then press ENTER.

MOTOROLA

ALE

NET# 7

MOTOROLA

ALE

NET	1	1
CALL	LQA	MON

24_________________________________________________________________________________________________

Image 38

Motorola MICOM-2ES/2RS/2TS ALE manual Transmitting Calls in ALE Mode, Selecting the Desired Net, To select a net

Contents

Supplement to Owner’s Guide MICOM-2ES/2RS/2TSALEHF-SSBTRANSCEIVERS Support for MIL-STD-188-141B IMRMB008Page COMMERCIAL WARRANTY STANDARD Phone FaxCOMPUTER SOFTWARE COPYRIGHTS Tallahassee 32310 FL, USA Motorola1720 West Paul Dirac Drive Cat. No. IMRMB008Page General Safety Precautions Warnings, Cautions and NotesInformation for Safe, Efficient Operation Product Safety and RF Exposure for MobileTwo-WayRadios Installed in Vehicles or as Fixed Site Control StationsFederal Communication Commission Regulations Communication Commission Regulations section Facilities Driver SafetyWhen using your radio while driving, please VehiclesPotentially Explosive Atmospheres Operational WarningsFor Vehicles with an Air Bag Blasting Caps and Blasting AreasTable of Contents PageMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Figure 1. Main Menu Menu UpdatesIntroduction Figure 2. Channel CH Menu permanently enabled using Menu Updatesreceived signal level display is not 2. The GPS item appears only when yourLANG MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuidePROG Menu ENGLISHPROG Menu Menu UpdatesLANG ENGLISHALE Addressing Method New ALE FeaturesSelective Calling Address and Call Types Individual Station AddressSpecial Addressing Modes - Use of Wildcards Net AddressesGroup Addresses Table 1. Use of “@” Stuffing Symbol ContTable 2. Use of “?” Wildcard Symbol AllCall Addresses Table 2. Use of “?” Wildcard Symbol ContNull Address AnyCallsSelf Addresses Inlink AddressUsing the MultiNet Feature Messages Using ALE Functions in the Channel ModeUsing the Caller Stack Quick CallALE and Rx Only or Tx Only Channels Entering the ALE ModeEnabling the ALE Mode ALE ProgrammingALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving a net call Receiving Calls in ALE ModeReceiving an individual call Receiving an AllCallReceiving a bidirectional handshake call Receiving an AnyCallReceiving a sounding call To answer an incoming callTo display LQA for the received call Link StateLink State Options BAND LQA F3RPL MORE, F1 FREQ MODERCLV To replace the channelUsing the Caller Stack To view the calls in the stackTo disconnect an incoming call Disconnecting CallsTo remove an address from the stack To select a net Transmitting Calls in ALE ModeSelecting the Desired Net To transmit an individual call with MultiNet OFF Calls to an Individual Station1234 To transmit an individual call with MultiNet ON LINK1234 To transmit on a specific channel 1234 Quick CallTo send a quick call Using Autodial To use Autodial to send a callSending Messages To transmit an individual call with a messageTo send a message during a call link state 1234Option Other Types of CallsTo select a special call type CapabilitiesCapabilities Transmitting AIICallsOption See Page …To send global AllCall using the ESC key To send global AllCall using the CALL functionTo send selective AllCall END CALLING 11.To end the call, press ESCLINK SL ALLCALL MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideTransmitting Net Calls To transmit a net callTransmitting Group Calls To transmit a group call LEASTTo define or change a group Transmitting AnyCalls To transmit an AnyCall NOT PROGANY @@2 CALLANY @@? ANY @59Transmitting Wildcard Calls To transmit a wildcard callNOT PROG AT LEASTTransmitting a Self Call To send a self-callBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net Sounding To manually initiate soundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode NET RCV ALE ProgrammingTo enter the ALE Programming mode DescriptionDIR AMD Programming NetsNet Programming Overview DescriptionNAME MEMB CHAN Default Values GET ERASHACK Setting the Net OptionsSLNT LQAR MACKAMD Message Configuration Directory ParametersMLQA QCAL ALE Options ConfigurationEXAL ALRT ILNK BDLK AMD Auto Dial ParametersStoring ALE Parameters Using the New Station Address Filter