Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE manual Auto Dial Parameters, Storing ALE Parameters, Amd

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 75

Auto Dial Parameters

ALE Programming

•	AMD	Yes
•	ILNK	No
•	BDLK	No

When configuring ALE options, you do not need to define all parameters – change only those for which the factory-default values are not suitable.

Auto Dial Parameters

Auto Dial enables you to set shortcuts for calls to frequently called stations, with or without automatically attaching messages when a station is called:

•AUTO Used to configure up to 10 autodial codes, numbered AUTO 0 to AUTO 9.

•AMD

Note

Used to prepare AMD messages for sending when an autodial code is used. See message preparation details on page 30.

If a message is attached to the address, an exclamation mark precedes the address.

Storing ALE Parameters

Before exiting the ALE programming menu, you must store the parameters you have programmed.

If you press the MENU or ESC key to exit the programming mode without first saving your changes, you will be prompted to store the Important ALE configuration changes. Press YES to store the configuration.

If you press NO, the configuration will revert to the previous configuration, and any changes made in the ALE programming session will be ignored.

_________________________________________________________________________________________________ 61

Image 75

Motorola MICOM-2ES/2RS/2TS ALE manual Auto Dial Parameters, Storing ALE Parameters, Amd

Contents

IMRMB008 MICOM-2ES/2RS/2TSALEHF-SSBTRANSCEIVERS Support for MIL-STD-188-141B Supplement to Owner’s GuidePage Phone Fax COMMERCIAL WARRANTY STANDARDCOMPUTER SOFTWARE COPYRIGHTS Cat. No. IMRMB008 Motorola1720 West Paul Dirac Drive Tallahassee 32310 FL, USAPage Warnings, Cautions and Notes General Safety PrecautionsSite Control Stations Product Safety and RF Exposure for MobileTwo-WayRadios Installed in Vehicles or as Fixed Information for Safe, Efficient OperationFederal Communication Commission Regulations Communication Commission Regulations section Vehicles Driver SafetyWhen using your radio while driving, please FacilitiesBlasting Caps and Blasting Areas Operational WarningsFor Vehicles with an Air Bag Potentially Explosive AtmospheresPage Table of ContentsMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Menu Updates IntroductionFigure 1. Main Menu Figure 2. Channel CH Menu 2. The GPS item appears only when your Menu Updatesreceived signal level display is not permanently enabled usingENGLISH MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuidePROG Menu LANGENGLISH Menu UpdatesLANG PROG MenuNew ALE Features Selective CallingALE Addressing Method Individual Station Address Address and Call TypesTable 1. Use of “@” Stuffing Symbol Cont Net AddressesGroup Addresses Special Addressing Modes - Use of WildcardsTable 2. Use of “?” Wildcard Symbol Table 2. Use of “?” Wildcard Symbol Cont AllCall AddressesInlink Address AnyCallsSelf Addresses Null AddressUsing the MultiNet Feature Quick Call Using ALE Functions in the Channel ModeUsing the Caller Stack MessagesALE Programming Entering the ALE ModeEnabling the ALE Mode ALE and Rx Only or Tx Only ChannelsALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving an AllCall Receiving Calls in ALE ModeReceiving an individual call Receiving a net callTo answer an incoming call Receiving an AnyCallReceiving a sounding call Receiving a bidirectional handshake callLink State Link State OptionsTo display LQA for the received call LQA F3 RPL MORE, F1BAND To replace the channel MODERCLV FREQTo view the calls in the stack Using the Caller StackDisconnecting Calls To remove an address from the stackTo disconnect an incoming call Transmitting Calls in ALE Mode Selecting the Desired NetTo select a net Calls to an Individual Station 1234To transmit an individual call with MultiNet OFF LINK 1234To transmit an individual call with MultiNet ON To transmit on a specific channel Quick Call To send a quick call1234 To use Autodial to send a call Using AutodialTo transmit an individual call with a message Sending Messages1234 To send a message during a call link stateCapabilities Other Types of CallsTo select a special call type OptionSee Page … Transmitting AIICallsOption CapabilitiesTo send global AllCall using the CALL function To send global AllCall using the ESC keyTo send selective AllCall MICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide 11.To end the call, press ESCLINK SL ALLCALL END CALLINGTo transmit a net call Transmitting Net CallsTransmitting Group Calls LEAST To transmit a group callTo define or change a group Transmitting AnyCalls NOT PROG To transmit an AnyCallANY @59 CALLANY @@? ANY @@2To transmit a wildcard call Transmitting Wildcard CallsAT LEAST NOT PROGTo send a self-call Transmitting a Self CallBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net To manually initiate sounding SoundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode Description ALE ProgrammingTo enter the ALE Programming mode NET RCVDescription Programming NetsNet Programming Overview DIR AMDNAME MEMB CHAN GET ERAS Default ValuesMACK Setting the Net OptionsSLNT LQAR HACKDirectory Parameters AMD Message ConfigurationALE Options Configuration EXAL ALRTMLQA QCAL ILNK BDLK Auto Dial Parameters Storing ALE ParametersAMD Using the New Station Address Filter