Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE Sounding, To manually initiate sounding

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 64

Sounding

MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide

Sounding

Sounding is used to test the quality of the channels and propagation paths of all channels in the net.

The sounding signal is normally repeated automatically, at regular intervals. A complete round of sounding messages, or "sounding cycle" can be programmed to 30, 60, 90, or 120 minutes, or can be set to OFF.

Sounding can also be initiated manually whenever necessary, even if automatic sounding is enabled.

➤To manually initiate sounding:

			MOTOROLA
	1.	Press LQA (F2) to enter the LQA menu.	LQA
	1.	Press LQA (F2) to enter the LQA menu.	BDIR	SOND	CHAN	SELs
			BDIR	SOND	CHAN	SELs
			MOTOROLA
	2.	Press SOND (F2).	SOND
	2.	Press SOND (F2).	SOUND OFF
			ON	OFF	CHAN	OK s

3.Press ON (F1) to start manual sounding, or OFF (F2) to stop an ongoing sounding process.

• The radio automatically returns to ALE mode when sounding is stopped.

Notes	• When the radio transmits a sounding signal, the Tx
	indication is visible.

50_________________________________________________________________________________________________

Image 64

Motorola MICOM-2ES/2RS/2TS ALE Sounding, To manually initiate sounding

Contents

MICOM-2ES/2RS/2TSALE HF-SSBTRANSCEIVERS Support for MIL-STD-188-141BSupplement to Owner’s Guide IMRMB008Page COMMERCIAL WARRANTY STANDARD Phone FaxCOMPUTER SOFTWARE COPYRIGHTS Motorola 1720 West Paul Dirac DriveTallahassee 32310 FL, USA Cat. No. IMRMB008Page General Safety Precautions Warnings, Cautions and NotesProduct Safety and RF Exposure for Mobile Two-WayRadios Installed in Vehicles or as FixedInformation for Safe, Efficient Operation Site Control StationsFederal Communication Commission Regulations Communication Commission Regulations section Driver Safety When using your radio while driving, pleaseFacilities VehiclesOperational Warnings For Vehicles with an Air BagPotentially Explosive Atmospheres Blasting Caps and Blasting AreasTable of Contents PageMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Introduction Menu UpdatesFigure 1. Main Menu Figure 2. Channel CH Menu Menu Updates received signal level display is notpermanently enabled using 2. The GPS item appears only when yourMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide PROG MenuLANG ENGLISHMenu Updates LANGPROG Menu ENGLISHSelective Calling New ALE FeaturesALE Addressing Method Address and Call Types Individual Station AddressNet Addresses Group AddressesSpecial Addressing Modes - Use of Wildcards Table 1. Use of “@” Stuffing Symbol ContTable 2. Use of “?” Wildcard Symbol AllCall Addresses Table 2. Use of “?” Wildcard Symbol ContAnyCalls Self AddressesNull Address Inlink AddressUsing the MultiNet Feature Using ALE Functions in the Channel Mode Using the Caller StackMessages Quick CallEntering the ALE Mode Enabling the ALE ModeALE and Rx Only or Tx Only Channels ALE ProgrammingALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving Calls in ALE Mode Receiving an individual callReceiving a net call Receiving an AllCallReceiving an AnyCall Receiving a sounding callReceiving a bidirectional handshake call To answer an incoming callLink State Options Link StateTo display LQA for the received call RPL MORE, F1 LQA F3BAND MODE RCLVFREQ To replace the channelUsing the Caller Stack To view the calls in the stackTo remove an address from the stack Disconnecting CallsTo disconnect an incoming call Selecting the Desired Net Transmitting Calls in ALE ModeTo select a net 1234 Calls to an Individual StationTo transmit an individual call with MultiNet OFF 1234 LINKTo transmit an individual call with MultiNet ON To transmit on a specific channel To send a quick call Quick Call1234 Using Autodial To use Autodial to send a callSending Messages To transmit an individual call with a messageTo send a message during a call link state 1234Other Types of Calls To select a special call typeOption CapabilitiesTransmitting AIICalls OptionCapabilities See Page …To send global AllCall using the ESC key To send global AllCall using the CALL functionTo send selective AllCall 11.To end the call, press ESC LINK SL ALLCALLEND CALLING MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideTransmitting Net Calls To transmit a net callTransmitting Group Calls To transmit a group call LEASTTo define or change a group Transmitting AnyCalls To transmit an AnyCall NOT PROGCALL ANY @@?ANY @@2 ANY @59Transmitting Wildcard Calls To transmit a wildcard callNOT PROG AT LEASTTransmitting a Self Call To send a self-callBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net Sounding To manually initiate soundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode ALE Programming To enter the ALE Programming modeNET RCV DescriptionProgramming Nets Net Programming OverviewDIR AMD DescriptionNAME MEMB CHAN Default Values GET ERASSetting the Net Options SLNT LQARHACK MACKAMD Message Configuration Directory ParametersEXAL ALRT ALE Options ConfigurationMLQA QCAL ILNK BDLK Storing ALE Parameters Auto Dial ParametersAMD Using the New Station Address Filter