Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE manual Ilnk Bdlk

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 74

MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide

•MNT MultiNet: enable/disable the scanning of multiple ALE nets. When enabled, this feature lets the radio communicate with stations in nets other than the currently selected net.

•MxCH Maximum Scan Channels: when MultiNet is enabled, the time needed for scanning all the nets may be rather long. This parameter is used to adapt the duration of the calling signal to the number of scanned net, to ensure that communications are not disrupted.

You can use automatic selection, or select a specific value in the range of 0 to 59 seconds.

•ANY AnyCall: enable/disable the sending of AnyCalls.

•WILD Wildcard: enable/disable the sending wildcard calls.

•AMD Automatic Message Display: enable/disable the sending of AMD messages.

•ILNK

•BDLK

Inlink: enable/disable the inlink facility, which enables notifying other call participants when each participant disconnects from the link. All participants must be programmed to use the same selection (either YES or NO).

Do not enable the inlink function when communicating with a radio that does not support the full ALE capabilities in accordance with MIL-STD-188-141B.

Bidirectional link: enable/disable the automatic setting up of a link on the best channel after a bidirectional handshake with an individual station.

The ALE options have the following factory-default values:

•	PTT Timeout	No timeout
•	Alert	Yes
•	External Alarm	Yes
•	Auto Address	No
•	Quick Call	Yes
•	Minimum LQA score	0
•	Accept Link Timeout	Yes
•	MNT	Yes
•	MxCH	Auto
•	ANY	Yes
•	WILD	Yes

60_________________________________________________________________________________________________

Image 74

Motorola MICOM-2ES/2RS/2TS ALE manual Ilnk Bdlk

Contents

Supplement to Owner’s Guide MICOM-2ES/2RS/2TSALEHF-SSBTRANSCEIVERS Support for MIL-STD-188-141B IMRMB008Page COMMERCIAL WARRANTY STANDARD Phone FaxCOMPUTER SOFTWARE COPYRIGHTS Tallahassee 32310 FL, USA Motorola1720 West Paul Dirac Drive Cat. No. IMRMB008Page General Safety Precautions Warnings, Cautions and NotesInformation for Safe, Efficient Operation Product Safety and RF Exposure for MobileTwo-WayRadios Installed in Vehicles or as Fixed Site Control StationsFederal Communication Commission Regulations Communication Commission Regulations section Facilities Driver SafetyWhen using your radio while driving, please VehiclesPotentially Explosive Atmospheres Operational WarningsFor Vehicles with an Air Bag Blasting Caps and Blasting AreasTable of Contents PageMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Figure 1. Main Menu Menu UpdatesIntroduction Figure 2. Channel CH Menu permanently enabled using Menu Updatesreceived signal level display is not 2. The GPS item appears only when yourLANG MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuidePROG Menu ENGLISHPROG Menu Menu UpdatesLANG ENGLISHALE Addressing Method New ALE FeaturesSelective Calling Address and Call Types Individual Station AddressSpecial Addressing Modes - Use of Wildcards Net AddressesGroup Addresses Table 1. Use of “@” Stuffing Symbol ContTable 2. Use of “?” Wildcard Symbol AllCall Addresses Table 2. Use of “?” Wildcard Symbol ContNull Address AnyCallsSelf Addresses Inlink AddressUsing the MultiNet Feature Messages Using ALE Functions in the Channel ModeUsing the Caller Stack Quick CallALE and Rx Only or Tx Only Channels Entering the ALE ModeEnabling the ALE Mode ALE ProgrammingALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving a net call Receiving Calls in ALE ModeReceiving an individual call Receiving an AllCallReceiving a bidirectional handshake call Receiving an AnyCallReceiving a sounding call To answer an incoming callTo display LQA for the received call Link StateLink State Options BAND LQA F3RPL MORE, F1 FREQ MODERCLV To replace the channelUsing the Caller Stack To view the calls in the stackTo disconnect an incoming call Disconnecting CallsTo remove an address from the stack To select a net Transmitting Calls in ALE ModeSelecting the Desired Net To transmit an individual call with MultiNet OFF Calls to an Individual Station1234 To transmit an individual call with MultiNet ON LINK1234 To transmit on a specific channel 1234 Quick CallTo send a quick call Using Autodial To use Autodial to send a callSending Messages To transmit an individual call with a messageTo send a message during a call link state 1234Option Other Types of CallsTo select a special call type CapabilitiesCapabilities Transmitting AIICallsOption See Page …To send global AllCall using the ESC key To send global AllCall using the CALL functionTo send selective AllCall END CALLING 11.To end the call, press ESCLINK SL ALLCALL MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideTransmitting Net Calls To transmit a net callTransmitting Group Calls To transmit a group call LEASTTo define or change a group Transmitting AnyCalls To transmit an AnyCall NOT PROGANY @@2 CALLANY @@? ANY @59Transmitting Wildcard Calls To transmit a wildcard callNOT PROG AT LEASTTransmitting a Self Call To send a self-callBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net Sounding To manually initiate soundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode NET RCV ALE ProgrammingTo enter the ALE Programming mode DescriptionDIR AMD Programming NetsNet Programming Overview DescriptionNAME MEMB CHAN Default Values GET ERASHACK Setting the Net OptionsSLNT LQAR MACKAMD Message Configuration Directory ParametersMLQA QCAL ALE Options ConfigurationEXAL ALRT ILNK BDLK AMD Auto Dial ParametersStoring ALE Parameters Using the New Station Address Filter