Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE manual Not Prog, At Least

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 59

AT LEAST 2.

New ALE Features

4.Press MORE again to display the next page.

5.Press WILD (F1) to start.

6.Press SEL (F4).

MOTOROLA

CALL

WILD SELF GRP ANYs

MOTOROLA

CALL

WILD

SEND PAGE CHAN SELs

MOTOROLA

WILD

_

? PAGE CHAN MONs

	If you try to send (SEND (F1)) the call without first selecting an
	address, your attempt is rejected and you see for a few seconds
Note	NOT PROG.
Note

7.Select the desired address:

•To insert a wildcard, press ? (F1).

•Enter the desired characters using the keypad

8.Confirm your selection by pressing ENTER.

MOTOROLA

WILD ?135?

?<-- --> CLR

MOTOROLA

CALL ?135?

SEND PAGE CHAN SELs

9.Press PAGE (F2) if you want to attach a message to the call.

10.Press CHAN (F3) if you want to initiate the call on a specific channel.

11.Press SEND (F1) or ENTER to initiate the call.

	If the selected group does not include at least 2 stations, your
	request is rejected and you will see for a few seconds the message
Note	AT LEAST 2.
Note

The radio now starts the process. During this process, you will see TO alternating with the number of the channel on which the request is being sent.

You can press STOP (F1) or ESC to abort the entire process.

Note

_________________________________________________________________________________________________ 45

Image 59

Motorola MICOM-2ES/2RS/2TS ALE manual Not Prog, At Least

Contents

IMRMB008 MICOM-2ES/2RS/2TSALEHF-SSBTRANSCEIVERS Support for MIL-STD-188-141B Supplement to Owner’s GuidePage Phone Fax COMMERCIAL WARRANTY STANDARDCOMPUTER SOFTWARE COPYRIGHTS Cat. No. IMRMB008 Motorola1720 West Paul Dirac Drive Tallahassee 32310 FL, USAPage Warnings, Cautions and Notes General Safety PrecautionsSite Control Stations Product Safety and RF Exposure for MobileTwo-WayRadios Installed in Vehicles or as Fixed Information for Safe, Efficient OperationFederal Communication Commission Regulations Communication Commission Regulations section Vehicles Driver SafetyWhen using your radio while driving, please FacilitiesBlasting Caps and Blasting Areas Operational WarningsFor Vehicles with an Air Bag Potentially Explosive AtmospheresPage Table of ContentsMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Figure 1. Main Menu Menu UpdatesIntroduction Figure 2. Channel CH Menu 2. The GPS item appears only when your Menu Updatesreceived signal level display is not permanently enabled usingENGLISH MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuidePROG Menu LANGENGLISH Menu UpdatesLANG PROG MenuALE Addressing Method New ALE FeaturesSelective Calling Individual Station Address Address and Call TypesTable 1. Use of “@” Stuffing Symbol Cont Net AddressesGroup Addresses Special Addressing Modes - Use of WildcardsTable 2. Use of “?” Wildcard Symbol Table 2. Use of “?” Wildcard Symbol Cont AllCall AddressesInlink Address AnyCallsSelf Addresses Null AddressUsing the MultiNet Feature Quick Call Using ALE Functions in the Channel ModeUsing the Caller Stack MessagesALE Programming Entering the ALE ModeEnabling the ALE Mode ALE and Rx Only or Tx Only ChannelsALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving an AllCall Receiving Calls in ALE ModeReceiving an individual call Receiving a net callTo answer an incoming call Receiving an AnyCallReceiving a sounding call Receiving a bidirectional handshake callTo display LQA for the received call Link StateLink State Options BAND LQA F3RPL MORE, F1 To replace the channel MODERCLV FREQTo view the calls in the stack Using the Caller StackTo disconnect an incoming call Disconnecting CallsTo remove an address from the stack To select a net Transmitting Calls in ALE ModeSelecting the Desired Net To transmit an individual call with MultiNet OFF Calls to an Individual Station1234 To transmit an individual call with MultiNet ON LINK1234 To transmit on a specific channel 1234 Quick CallTo send a quick call To use Autodial to send a call Using AutodialTo transmit an individual call with a message Sending Messages1234 To send a message during a call link stateCapabilities Other Types of CallsTo select a special call type OptionSee Page … Transmitting AIICallsOption CapabilitiesTo send global AllCall using the CALL function To send global AllCall using the ESC keyTo send selective AllCall MICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide 11.To end the call, press ESCLINK SL ALLCALL END CALLINGTo transmit a net call Transmitting Net CallsTransmitting Group Calls LEAST To transmit a group callTo define or change a group Transmitting AnyCalls NOT PROG To transmit an AnyCallANY @59 CALLANY @@? ANY @@2To transmit a wildcard call Transmitting Wildcard CallsAT LEAST NOT PROGTo send a self-call Transmitting a Self CallBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net To manually initiate sounding SoundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode Description ALE ProgrammingTo enter the ALE Programming mode NET RCVDescription Programming NetsNet Programming Overview DIR AMDNAME MEMB CHAN GET ERAS Default ValuesMACK Setting the Net OptionsSLNT LQAR HACKDirectory Parameters AMD Message ConfigurationMLQA QCAL ALE Options ConfigurationEXAL ALRT ILNK BDLK AMD Auto Dial ParametersStoring ALE Parameters Using the New Station Address Filter