Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE manual To send selective AllCall

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 49

➤To send selective AllCall:

New ALE Features

➤To send selective AllCall:

1.Press CALL (F1).

The radio displays the last called address.

2.Press MORE once.

3.Press MULT (F1) to display the first page of special calls.

4.Press ALL (F1).

5.Press SEL (F4).

If you decide to send a Global AllCall, press GLOB (F3).

Note

6.Type the desired character (only one character is accepted).

You can press ? (F1) if you decide to send a global AllCall or “?”.

Note

7. Confirm your selection by pressing ENTER.

If you decide to send a global AllCall, press GLOB (F3) or “?”.

Note

8.Press SEND (F1) or ENTER to start the call. The radio starts sending the selective AllCall.

	While the radio is initializing the link,
	you can press STOP (F1) or ESC to
Note	abort the entire process.
Note

MOTOROLA

CALL 1001

SEND PAGE CHAN MONs

MOTOROLA

CALL

GL ALLCALL

MULT PAGE CHAN MONs

MOTOROLA

CALL

ALL NET GRP ANYs

MOTOROLA

CALL

GL ALLCALL

SEND PAGE GLOB SEL

MOTOROLA

ALL

EDIT:_

?PAGE CHAN MONs

MOTOROLA

ALL

EDIT:5

?PAGE CHAN CLRs

MOTOROLA

CALL

SL ALLCALL

SEND PAGE GLOB SELs

MOTOROLA

TO

SL ALLCALL

STOP PAGE GLOB SELs

MOTOROLA

CH 2

SL ALLCALL

STOP PAGE GLOB SELs

_________________________________________________________________________________________________ 35

Image 49

Motorola MICOM-2ES/2RS/2TS ALE manual To send selective AllCall

Contents

HF-SSBTRANSCEIVERS Support for MIL-STD-188-141B MICOM-2ES/2RS/2TSALESupplement to Owner’s Guide IMRMB008Page Phone Fax COMMERCIAL WARRANTY STANDARDCOMPUTER SOFTWARE COPYRIGHTS 1720 West Paul Dirac Drive MotorolaTallahassee 32310 FL, USA Cat. No. IMRMB008Page Warnings, Cautions and Notes General Safety PrecautionsTwo-WayRadios Installed in Vehicles or as Fixed Product Safety and RF Exposure for MobileInformation for Safe, Efficient Operation Site Control StationsFederal Communication Commission Regulations Communication Commission Regulations section When using your radio while driving, please Driver SafetyFacilities VehiclesFor Vehicles with an Air Bag Operational WarningsPotentially Explosive Atmospheres Blasting Caps and Blasting AreasPage Table of ContentsMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Introduction Menu UpdatesFigure 1. Main Menu Figure 2. Channel CH Menu received signal level display is not Menu Updatespermanently enabled using 2. The GPS item appears only when yourPROG Menu MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideLANG ENGLISHLANG Menu UpdatesPROG Menu ENGLISHSelective Calling New ALE FeaturesALE Addressing Method Individual Station Address Address and Call TypesGroup Addresses Net AddressesSpecial Addressing Modes - Use of Wildcards Table 1. Use of “@” Stuffing Symbol ContTable 2. Use of “?” Wildcard Symbol Table 2. Use of “?” Wildcard Symbol Cont AllCall AddressesSelf Addresses AnyCallsNull Address Inlink AddressUsing the MultiNet Feature Using the Caller Stack Using ALE Functions in the Channel ModeMessages Quick CallEnabling the ALE Mode Entering the ALE ModeALE and Rx Only or Tx Only Channels ALE ProgrammingALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving an individual call Receiving Calls in ALE ModeReceiving a net call Receiving an AllCallReceiving a sounding call Receiving an AnyCallReceiving a bidirectional handshake call To answer an incoming callLink State Options Link StateTo display LQA for the received call RPL MORE, F1 LQA F3BAND RCLV MODEFREQ To replace the channelTo view the calls in the stack Using the Caller StackTo remove an address from the stack Disconnecting CallsTo disconnect an incoming call Selecting the Desired Net Transmitting Calls in ALE ModeTo select a net 1234 Calls to an Individual StationTo transmit an individual call with MultiNet OFF 1234 LINKTo transmit an individual call with MultiNet ON To transmit on a specific channel To send a quick call Quick Call1234 To use Autodial to send a call Using AutodialTo transmit an individual call with a message Sending Messages1234 To send a message during a call link stateTo select a special call type Other Types of CallsOption CapabilitiesOption Transmitting AIICallsCapabilities See Page …To send global AllCall using the CALL function To send global AllCall using the ESC keyTo send selective AllCall LINK SL ALLCALL 11.To end the call, press ESCEND CALLING MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideTo transmit a net call Transmitting Net CallsTransmitting Group Calls LEAST To transmit a group callTo define or change a group Transmitting AnyCalls NOT PROG To transmit an AnyCallANY @@? CALLANY @@2 ANY @59To transmit a wildcard call Transmitting Wildcard CallsAT LEAST NOT PROGTo send a self-call Transmitting a Self CallBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net To manually initiate sounding SoundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode To enter the ALE Programming mode ALE ProgrammingNET RCV DescriptionNet Programming Overview Programming NetsDIR AMD DescriptionNAME MEMB CHAN GET ERAS Default ValuesSLNT LQAR Setting the Net OptionsHACK MACKDirectory Parameters AMD Message ConfigurationEXAL ALRT ALE Options ConfigurationMLQA QCAL ILNK BDLK Storing ALE Parameters Auto Dial ParametersAMD Using the New Station Address Filter