Manuals / Motorola / Household Appliance / Home Security System

Motorola MICOM-2ES/2RS/2TS ALE manual Transmitting a Self Call, To send a self-call

Models: MICOM-2ES/2RS/2TS ALE

1 76

Download 76 pages 32.79 Kb

Page 60

Transmitting a Self Call

MICOM-2ES/2RS/2TS ALE Supplement to Owner’s Guide

12.After a delay, you will see LINK with the wildcard address flashing.

13.Confirm the link set up by pressing ENTER or the PTT. The address stops flashing, and you can start talking.

MOTOROLA

LINK ?135?

SEND PAGE LQA MONs

MOTOROLA

LINK ?135?

SEND PAGE LQA MONs

MOTOROLA

14. To end the call, press ESC.

END CALLING

Transmitting a Self Call

The self-call is a test call addressed to your own address within the currently selected net. Its purpose is to check that your radio set is OK and can transmit calls (to check reception, you can simply listen to other radio sets).

When you send the self-call, the radio starts sending calls to its own address, successively, on each channel in the current net. After going through all the channels, the call process stops. No other response is expected.

You can also include the self address in a group call.

Note

➤To send a self-call:

1.Press CALL (F1).

The radio displays the last called address.

2.Press MORE once.

3.Press MULT (F1) to display the first page of special calls.

4.Press MORE again to display the next page.

MOTOROLA

CALL 1001

SEND PAGE CHAN MONs

MOTOROLA

CALL 1001

MULT PAGE CHAN MONs

MOTOROLA

CALL

ALL NET GRP ANYs

MOTOROLA

CALL

WILD SELF GRP ANYs

46_________________________________________________________________________________________________

Image 60

Motorola MICOM-2ES/2RS/2TS ALE manual Transmitting a Self Call, To send a self-call

Contents

MICOM-2ES/2RS/2TSALE HF-SSBTRANSCEIVERS Support for MIL-STD-188-141BSupplement to Owner’s Guide IMRMB008Page COMMERCIAL WARRANTY STANDARD Phone FaxCOMPUTER SOFTWARE COPYRIGHTS Motorola 1720 West Paul Dirac DriveTallahassee 32310 FL, USA Cat. No. IMRMB008Page General Safety Precautions Warnings, Cautions and NotesProduct Safety and RF Exposure for Mobile Two-WayRadios Installed in Vehicles or as FixedInformation for Safe, Efficient Operation Site Control StationsFederal Communication Commission Regulations Communication Commission Regulations section Driver Safety When using your radio while driving, pleaseFacilities VehiclesOperational Warnings For Vehicles with an Air BagPotentially Explosive Atmospheres Blasting Caps and Blasting AreasTable of Contents PageMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide Menu Updates IntroductionFigure 1. Main Menu Figure 2. Channel CH Menu Menu Updates received signal level display is notpermanently enabled using 2. The GPS item appears only when yourMICOM-2ES/2RS/2TSALE Supplement to Owner’s Guide PROG MenuLANG ENGLISHMenu Updates LANGPROG Menu ENGLISHNew ALE Features Selective CallingALE Addressing Method Address and Call Types Individual Station AddressNet Addresses Group AddressesSpecial Addressing Modes - Use of Wildcards Table 1. Use of “@” Stuffing Symbol ContTable 2. Use of “?” Wildcard Symbol AllCall Addresses Table 2. Use of “?” Wildcard Symbol ContAnyCalls Self AddressesNull Address Inlink AddressUsing the MultiNet Feature Using ALE Functions in the Channel Mode Using the Caller StackMessages Quick CallEntering the ALE Mode Enabling the ALE ModeALE and Rx Only or Tx Only Channels ALE ProgrammingALE Mode Options Receiving and Transmitting Calls in ALE Mode Receiving Calls in ALE Mode Receiving an individual callReceiving a net call Receiving an AllCallReceiving an AnyCall Receiving a sounding callReceiving a bidirectional handshake call To answer an incoming callLink State Link State OptionsTo display LQA for the received call LQA F3 RPL MORE, F1BAND MODE RCLVFREQ To replace the channelUsing the Caller Stack To view the calls in the stackDisconnecting Calls To remove an address from the stackTo disconnect an incoming call Transmitting Calls in ALE Mode Selecting the Desired NetTo select a net Calls to an Individual Station 1234To transmit an individual call with MultiNet OFF LINK 1234To transmit an individual call with MultiNet ON To transmit on a specific channel Quick Call To send a quick call1234 Using Autodial To use Autodial to send a callSending Messages To transmit an individual call with a messageTo send a message during a call link state 1234Other Types of Calls To select a special call typeOption CapabilitiesTransmitting AIICalls OptionCapabilities See Page …To send global AllCall using the ESC key To send global AllCall using the CALL functionTo send selective AllCall 11.To end the call, press ESC LINK SL ALLCALLEND CALLING MICOM-2ES/2RS/2TSALE Supplement to Owner’s GuideTransmitting Net Calls To transmit a net callTransmitting Group Calls To transmit a group call LEASTTo define or change a group Transmitting AnyCalls To transmit an AnyCall NOT PROGCALL ANY @@?ANY @@2 ANY @59Transmitting Wildcard Calls To transmit a wildcard callNOT PROG AT LEASTTransmitting a Self Call To send a self-callBidirectional Handshake 1.Press LQA F2 to enter the LQA menu To execute a bidirectional handshake with a net Sounding To manually initiate soundingUsing the Inlink Function Transmitting ALE Calls in the Channel Mode ALE Programming To enter the ALE Programming modeNET RCV DescriptionProgramming Nets Net Programming OverviewDIR AMD DescriptionNAME MEMB CHAN Default Values GET ERASSetting the Net Options SLNT LQARHACK MACKAMD Message Configuration Directory ParametersALE Options Configuration EXAL ALRTMLQA QCAL ILNK BDLK Auto Dial Parameters Storing ALE ParametersAMD Using the New Station Address Filter