USE Defaults | Multiquip DCA85usJ2 specs

DIAGNOSTIC DISPLAY

3.Once the “Setup 1-up Display” menu icon has been highlighted touch the “Enter Button” to access the “Setup 1-up display” function.

GO TO 1-UP DISPLAY

STORED CODES

ENGINE CONFG

SETUP 1-UP DISPLAY

SETUP-4-UP DISPLAY

SELECT UNITS

ADJUST BACKLIGHT

4.Three options are available for modiﬁ cation of the 1-Up display.

a.Use Defaults — This option contains a set of engine parameters: Engine Hours, Engine RPM. System Voltage, Battery Voltage, % Engine Load at Current RPM, Coolant Temperature, Oil Pressure.

b.Custom Setup — This option allows for the modiﬁ cation of what parameter, the number of parameters, and the order in which the parameters are being displayed.

c.Automatic Scan — Selecting the scan function will cause the 1-Up Display to scroll through the selected set of parameters one at a time, momentarily pausing at each.

5.Use Defaults- To select “Use Defaults” use the arrow buttons to scroll to and highlight “Use Defaults” in the menu display.

USE DEFAULTS

CUSTOM SETUP

AUTOMATIC SCAN OFF

7.A message indicating the “Single Engine” parameter display parameters are reset to the factory defaults will be displayed, then the display will return to the “Custom Setup” menu.

RESTORED TO

DEFAULTS

8.Custom Setup- To perform a custom setup of the 1-Up Display, use the arrow buttons to scroll to and highlight “Custom Setup” on the display.

USE DEFAULTS

CUSTOM SETUP

AUTOMATIC SCAN OFF

9.Touching the “Enter Button” will display a list of engine parameters.

USE DEFAULTS

CUSTOM SETUP

AUTOMATIC SCAN OFF

10.Use the “Arrow Buttons” to scroll to and highlight a selected parameter (parameter with a # symbol to right of it).

6.Touch the “Enter Button” to activate the “Use Defaults” function.

USE DEFAULTS

CUSTOM SETUP

AUTOMATIC SCAN OFF

ENGINE SPEED	1
PERCENT LOAD AT CURRENT RPM 3
ENGINE OIL PRESSURE	2
ENGINE COOLANT TEMPERATURE

This number indicates the order of display for the parameters and that the parameter is selected

for display.

PAGE 28 — DCA85USJ2 60 HZ GENERATOR • OPERATION AND PARTS MANUAL — REV. #1 (03/22/11)

Image 28

Multiquip DCA85usJ2 manual USE Defaults

Contents

Model DCA85USJ2 This Manual Must Accompany the Equipment AT ALL Times Proposition 65 Warning Reporting Safety Defects Administrator Table of Contents DCA-85USJ2 Generator Parts Ordering Procedures Ordering parts has never been easier Safety Information Safety Messages Generator Safety General Safety Always know the location of the nearest Engine Safety Before servicing equipment Fuel Safety Towing Safety Never use fuel as a cleaning agent From fuel vapors or if fuel is spilled on a hot engine Electrical Safety Grounding SafetyPower Cord/Cable Safety Device. All installations should be Battery Safety Environmental Safety Specifications DCA-85USJ2 Dimensions Dimensions Installation Typical Generator Grounding Application Outdoor Installation Indoor InstallationMounting Generator Grounding General Information Major Components Item no Display Parameters Diagnostic DisplayMenu Button Press this button to enter or exit menu screens Main Menu Navigation First Time Start UpSelecting a Language Stored Fault Codes Engine Conﬁguration Data First Time Start-Up Touch the Menu Button to return to the main menu Auxiliary Gage Fault Faults and WarningDisplay will return to the single or four parameter screen Active Fault Codes Fault Code Bachlight Adjustment Shutdown Codes Contrast Adjustment Setup 1-UP Display Select Units USE Defaults Automatic Scan on Select the 4-Up Custom Setup from the 4-Up Setup menu Setup 4-Up DisplayTouch the Enter Button and a list of parameters will appear Utilities information and troubleshooting Functions Touch Menu Button to return to the Utilities menu Modbus Setup When ﬁ nished, touch Menu to return to the previous screen Data Error Timeout ECU not RespondingCanbus Failure No Data Generator Control Panel OFF Engine Operating Panel OFF Engine Operating Panel Output Terminal Familiarization Output Terminal Panel FamiliarizationTerminal legs O and Ground are considered bonded grounds Removing the Plastic Face Plate Hard Wire Hookup Panel VAC Gfci Receptacles Connecting Loads Over Current Relay Three Phase Load Single Phase LoadLoad Application Generator Outputs Generator Output Voltages HOW to Read the AC Ammeter and AC Voltage Gauges Generator OUTPUTS/GAUGE ReadingAC Voltmeter Gauge Reading AC Ammeter Gauge Reading Output Terminal Panel Connections Uvwo Terminal Output Voltages3Ø-240/139 Uvwo Terminal Output Voltages 3Ø-208V/1Ø-120V Uvwo Terminal Output Voltages 3Ø-480/277V Uvwo Terminal Output Voltages 1Ø-240/120V Uvwo Terminal Output Voltages INSPECTION/SETUP Circuit BreakersLubrication OIL Fuel Check Refueling Procedure Only use #2 diesel fuel when refueling Cleaning the Radiator AIR Cleaner FAN Belt TensionCoolant ANTIFREEZE/SUMMER COOLANT/ Water Operation in Freezing Weather Battery Battery Cable InstallationWiring Alternator Generator START-UP Procedure Manual Mode Before StartingStarting Starting Manual Engine Speed Switch High Before connecting this generator to any Starting Auto ModeWithout this transfer switch Normal Shutdown Procedure Generator SHUT-DOWN ProceduresEmergency Shutdown Procedure General Inspection AIR Cleaner MaintenanceAir Cleaner with Dust Indicator Fuel Tank Inspection Fuel AdditionAIR Removal Radiator Cleaning Check OIL LevelReplacing Oil Filter Flushing OUT Radiator and Replacing Coolant Trailer Maintenance Trailer MaintenanceCoupler Type of hitch used on the trailer for towing Brake Adjustment BrakesHydraulic Surge Brakes Actuator Tire Wear/Inﬂation TIRES/WHEELS/LUG NutsSuspension Lug Nut Torque Requirements Never use an pneumatic air gun to tighten wheel lug nuts Trailer Wiring Diagram Trailer/Towing Vehicle Wiring Diagram Generator Wiring Diagram Generator Wiring Diagram Engine Wiring Diagram Engine Wiring Diagram Troubleshooting Generator Troubleshooting Engine Controller Clean/repair radiator grillAdjust governor actuator Adjust governor controller Sample Parts List Explanation of Code in Remarks Column Suggested Spare Parts To 3 units Generator Assy 8101070033 00128100358101611004 8101015003 Control BOX Assy M2213001702 M22130017120330000180 0330000280 Control BOX Assy M4266600004 060180221833A 0601806653 33B 0601802149 Control BOX Assy M3223100004 0027105010M9220100004 0080200007 Engine and Radiator Assy M2923200094 R135680RE504836 RE529643 Engine and Radiator Assy 0605511395 06055113990603306395 0603306399 Output Terminal Assy M3230700003 M9220100304M9220100404 0039316000 Battery Assy 0602220199 M9310500014M9103000304 0602220920 Muffler Assy M2330101303 0017112030M2333001603 M2333200204 Fuel Tank Assy M2363000902 06055050700605501073 0605516090 Enclosure 1 Assy M2413002202 M23633007030016910030 0603306797 Enclosure 1 Assy M2463200603 34A M2493502104M2463400203 M2423200814 Enclosure 2 Assy M3443001902 M3493308603M3443002004 M2443400003 Enclosure 2 Assy 29A C9312500004 30A 0030006000M9110100804 M9110100904 Rubber Seals Assy 0229201240 02292011300314502550 0229200125 Nameplate and Decals Assy M1550000204 M1550002203M2550002603 M2550002613 Terms and Conditions of Sale Parts Freight PolicyPage HERE’S HOW to GET Help