Machine Operation and Safety Decals | Multiquip Sp-6065 instruction

MACHINE OPERATION AND SAFETY DECALS

The Multiquip SP-6065 Saw is equipped with a number of operation and safety decals. Should any of these decals become unreadable, replacements can be obtained from your dealer.

	P/N 15582		WARNING	P/N 15580
	P/N 15582

			KEEP FEET
			CLEAR
			P/N 25250-001
	WARNING!
KEEP HANDS
	CLEAR
P/N 25249-001
			P/N 15581
	CAUTION
When Larger Blade and Guard
is Installed, Belt Drive MUST
Be Changed to Proper Size.				P/N 22122-001
See Owners Manual.			P/N 11247 (ISO Black)
FAILURE TO COMPLY WITH THE C C AH
JADV EEE AV EEA OIEJGGVCBVVZ
S.M.I. MASONRY AND CONCRETE			P/N 36099 (ISO Blue)
SAW MANUFACTURER’S INSTITUTE
P/N 23330-001
P/N 25491			P/N 25678	P/N 13118
				P/N 13118
				MODEL
				SERIAL NO.
CHECK	LUBRICATION	HOT	BELT DRIVE
DECAL SHEET INTL STDS				CONTACT MULTIQUIP
	P/N 11246			SERVICE DEPARTMENT

16

Image 16

Multiquip Sp-6065 operation manual Machine Operation and Safety Decals

Contents

SP-6065 Concrete Saw For Help & Information Contact Multiquip Conventions California Proposition 65 Warning Table of Contents Specifications Safety Hazard Symbols Rotating Blades Skin Injection Hazard General Safety Warnings Rules for Safe OperationPage General Safety Precautions Blade Safety SAW Transportation Safety Machine Operation and Safety Decals Serial Tag Model no SPEC. no Serial no Serial TAG Operation Before Starting Engine Power, Cutting Power & Sheave Size Blade Shaft Ratios 18600 Blade RPM vs. Surface Feet Per Minute Sfpm Installing the Blade Installing the Blade Stacking Blades for Wide Cuts Blade Stacking Installing and Removing the Blade Guard Installing the Blade Guard Blade Guard Water Supply Installing the Collar Guard Collar Guard, Installed Water Supply and Control Water Supply System Control Panel ON-OFF Handlebars Handlebar Positions Similar to illustration Fueling the Saw Fuel System ON/OFF Switch, Choke, Throttle Locations Starting and Stopping the Engine Block Heaters Pointer AdjustmentDraining the Water System Pointer Adjustment Setting the Depth Indicator Raise Lower Controls Setting the Depth Stop Drive System Drive System Controls Transaxle Transaxle Transportation Tie-downs and Lift Point Night LightTie-downs Lift Point Lift Point Maintenance Removable Guards and Access Panels Belts and Pulleys Belt Tension Adjusting Blade Shaft Drive Belt Tension Engine Mount Lock Bolts Replacing the Blade Shaft Belt Replacing the Jackshaft Belt Rotary Belt Tensioner Do not OVER-TIGHTEN Blade Shaft Maintenance Blade Shaft Replacement Blade Collar Removal/Installation Removing the Inner Blade Collar Installing the Inner Blade Collar Installing the Inner Blade Collar Inner Collar Blade Shaft Maximum Cut Depth Adjustment Circuit Breakers Lubrication Air and Oil Filter Chart Engine PTO Drive Maintenance Attaching the PTO Bearing Puller to the Drive Plate Assembly PTO Drive Sheave/Bearing Assembly Re-Assembling the PTO Drive Replacing the Battery Rotate Engine Forward to Remove the Battery Raise/Lower Troubleshooting Raise-Lower System Joystick Tension Adjustment Joystick Adjustment Hydraulic System Maintenance Routine Maintenance Draining & Filling the Hydraulic System To drain the hydraulic system To fill the hydraulic system with oil Bleeding the Depth Stop Cylinder Bleeding the Depth Stop Cylinder Drive Wheel Alignment Drive Wheel Alignment Pivot Side Adjustment Side Specifications Dimensions and Weights Www multiquip.com