National Instruments NI 4070/4072 6 1/2-Digit FlexDMM - page 46

NI 4070/4072 Calibration Procedure 46 ni.com

46. Call niDMM_CalAdjustOffset with the following parameters:

•Mode = NIDMM_VAL_4_WIRE_RES

•Range = 10e3

•Input Resistance = NIDMM_VAL_RESISTANCE_NA

47. Call niDMM_CalAdjustMisc with Type set to

NIDMM_EXTCAL_MISCAL_RREF.

48. Call niDMM_SelfCal to self-calibrate the NI 4070/4072.

49. Output 0 Ω on the calibrator with external sense turned on but with

2-wire compensation turned off.

50. Call niDMM_CalAdjustOffset with the following parameters:

•Mode = NIDMM_VAL_4_WIRE_RES

•Range = 10e6

•Input Resistance = NIDMM_VAL_RESISTANCE_NA

51. Call niDMM_CalAdjustOffset with the following parameters:

•Mode = NIDMM_VAL_4_WIRE_RES

•Range = 1e6

•Input Resistance = NIDMM_VAL_RESISTANCE_NA

52. Call niDMM_CalAdjustOffset with the following parameters:

•Mode = NIDMM_VAL_4_WIRE_RES

•Range = 1e3

•Input Resistance = NIDMM_VAL_RESISTANCE_NA

53. Call niDMM_CalAdjustOffset with the following parameters:

•Mode = NIDMM_VAL_4_WIRE_RES

•Range = 100

•Input Resistance = NIDMM_VAL_RESISTANCE_NA

54. Remove the Fluke 5440 cables from the NI4070/4072, leaving the

other end of the cables connected to the calibrator.

55. Plug in the insulated shorting bar across the HI and LO banana plug

connectors of the NI 4070/4072.

56. Wait two minutes for the thermal EMF to stabilize.

57. Call niDMM_CalAdjustOffset with the following parameters:

•Mode = NIDMM_VAL_2_WIRE_RES

•Range = 10e6

•Input Resistance = NIDMM_VAL_RESISTANCE_NA

Contents

Main CALIBRATION PROCEDURE NI 4070/4072 6-Digit FlexDMM Contents Conventions Software Requirements Documentation Requirements Calibration Function Reference Password Calibration Interval Test Equipment Required Test Equipment Requirements for All NI 4070/4072 Devices Additional Requirements for the NI 4072 Optional Test Equipment Test Conditions Calibration Procedures Initial Setup Verification Procedures Verifying DC Voltage Page NI 4070/4072 Calibration Procedure 10 ni.com Figure 1. Cable Connections for Voltage and 2-Wire Resistance niDMM_SetAttributeViReal64 with the following parameters: Attribute_ID = Attribute_Value = NIDMM_VAL_GREATER_THAN_10_GIGAOHM 1 NI4070/4072 2 Fluke 5700A/5720A Calibrator 3 Fluke 5440 Cable Table 1. Fluke 5440 Cable Connections BananaPlug Connector (NI4070/4072) Banana Plug Color (Fluke 5440Cable) Page Page Page Page Verifying AC Voltage Page Page Page Page Page Page Verifying 4-Wire Resistance Page Verifying 2-Wire Resistance Page Page Page Page Page Verifying DC Current Page Page Verifying AC Current Verifying Frequency Page Page Verifying Capacitance and Inductance (NI 4072 Only) Page Page Page Adjustment Procedures Setting Up the Test Equipment Adjusting DC Voltage and Resistance Page Page Page Page Page Adjusting AC Voltage (AC- and DC-Coupled) Modes Page Page Page Table 13. niDMM_CalAdjustACFilter Parameters (Continued) Adjusting Current Modes Page Page Adjusting Capacitance and Inductance (NI 4072 Only) Page Completing the Adjustment Procedures Verification Limits DC Voltage AC Voltage Table 16. NI 4070/4072 AC Voltage Verification Limits Table 15. NI 4070/4072 DC Voltage Verification Limits (Continued) Table 16. NI 4070/4072 AC Voltage Verification Limits (Continued) 4-Wire Resistance Note Tolerances are provided for 4-wire resistance instead of absolute limits because the limits depend on the actual resistance value output by your calibrator. 2-Wire Resistance Note Tolerances are provided for 2-wire resistance instead of absolute limits because the DC Current AC Current Table 19. NI 4070/4072 DC Current Verification Limits Table 20. NI 4070/4072 AC Current Verification Limits Table 18. NI 4070/4072 2-Wire Resistance Verification Tolerances (Continued) Frequency Capacitance and Inductance Note Because the actual capacitance verification values can differ from the following values, Table22 provides tolerances that correspond to the NI 4072 accuracy specifications Table 21. Frequency Limits Appendix A: Calibration Options Page Figure 4. Verification Procedures Flowchart NI 4070/4072 Calibration Procedure 66 ni.com Figure 5. Adjustment Procedures Flowchart National Instruments Corporation 67 NI 4070/4072 Calibration Procedure Where to Go for Support