Any listed 2100 UL 103 HT. TYPE Chimney

C. Vertical exit using (6" DVL Close Clearance pipe, and

any listed 2100° UL 103 HT. TYPE Chimney).

Without optional close clearance shield, and pipe shield.

Model 21 minimum clearance to combustibles.

Figure 11.

Figure 12.

		BACK WALL			CONTEMPORARY CAP
					CONTEMPORARY CAP
		B	D FF	LISTED 2100° UL 103 HT
		B	G	LISTED 2100° UL 103 HT
WALLSIDE				TYP. CHIMNEY
		PROTECTOR			CAULK
		PROTECTOR			STORM COLLAR
					STORM COLLAR
	EE			G	FLASHING
	A			RADIATION SHIELD	FLASHING
	A

				LISTED 2100° UL 103 HT TYP.
				INSTALLATION
				CEILING	CEILING SUPPORT
				CEILING
					DVL CLOSE CLEAR-
					ANCE PIPE OR
					SHIELDED
	CC		C	SIDE
	CC		C	WALL

	A	B	C	D	E	F	G
MODEL 21	23”	9" 9" 11.5"			8"	3"	16"	NEW BUCK
								BUCK STOVE

NOTE: All clearances are to combustibles without close clearance shields, and pipe shield, using DVL Close Clearance pipe , and minimum floor protector.protector . The clearances above may be reduced. Follow NFPA-211codes if available or follow instructions on (Pages 22, and 23).

Page 21

Image 21

New Buck Corporation any listed 2100 UL 103 HT. TYPE Chimney, Model 21 minimum clearance to combustibles

Contents

MODEL NON-CATALYTICUNIT MODEL NON-CATBuck Stove Page TABLE OF CONTENTS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS MODELREAD THIS FIRST IMPORTANT INSTRUCTIONS INTRODUCTION SECTION MASONRY INSERT INSTALLATION SECTIONMODEL Floor Protection POSSIBLE TOOLS NEEDED FOR INSTALLATION INSTALLATION PREPARATIONMASONRY INSERT INSTALLATION OPTIONS OR WIRE IT OPEN AIRTIGHT INSU LATED CLEAN OUT REMOVE DAMPERSTARTER PIPE SEAL TRIM PANELS AND UNDER FRONT OF STOVE UNIT WITH INSULATION OR HIGH POSITIONING POSITIONING THE HEATERMOUNTING THE TRIM PANELS FIGURE 3 MOUNTING TRIM PANELS FINAL CHECK Page SECTION PRE-FABINSERT INSTALLATION Chimney PREPARING THE STOVE FOR INSTALLATION Floor Protection 1. Convert specification to R-value Residential Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLPREPARING THE ROOM HEATER LOCATION CHIMNEY Model 21 minimum clearance to combustibles HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential InstallationNOTE For minimum clearances See Page 17, Figure Model 21 minimum clearance to combustibles HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationWithout close clearance shield and pipe shield NOTE For minimum clearances See Page 19, Figure Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationD. Vertical Wall Exit using 6 DVL Close Clearance Pipe, and Elbow, and any Listed 2100 UL HT chimney and Listed 2100 UL HT T-Boxassembly Model 21 minimum clearance to combustibles Listed 2100 UL HT T-Boxassembly HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationNOTE For minimum clearances See Page 23, Figure Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationNOTE For minimum clearances See Page 25, Figure Listed 2100 UL HT T-Boxassembly OUT SIDE AIR INSTALLATION Page FINAL CHECK SECTION ALCOVE INSTALLATION AND CLEARANCES PREPARING THE STOVE FOR INSTALLATIONChimney Floor Protection 1. Convert specification to R-value HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Alcove Installation ALCOVE INSTALLATION AND CLEARANCES any listed 2100 UL 103 HT. TYPE ChimneyModel 21 minimum clearance to combustibles Installation of Optional Pipe Shield Installation of Optional Close Clearance ShieldsPipe Shield Loosen these top shield screws 13/16” TYP 1” TYP 1/4” TYP FINAL CHECK SECTION WOOD HEATER SAFETY BUILDING A FIRE SECTION OPERATION PROBLEM SECTION TROUBLESHOOTINGSOLUTION POSSIBLE CAUSE PROBLEM SOLUTIONPOSSIBLE CAUSE PROCEDURE WARRANTY TIME PERIODSNEW BUCK CORPORATION NBC PRODUCTS COVERED OTHER RIGHTS CONDITIONS AND EXCLUSIONS

New Buck Corporation installation instructions any listed 2100 UL 103 HT. TYPE Chimney

Models: 21

any listed 2100° UL 103 HT. TYPE Chimney).