Listed 2100 UL HT T-Boxassembly | New Buck Corporation specification

F. Vertical wall exit using (6" DVL Close Clearance pipe with elbow and any listed 2100° UL 103 HT. TYPE Chimney, and

Listed 2100° UL HT T-Box assembly).

With optional close clearance shield and pipe shield. Model 21 minimum clearance to combustibles.

BACK WALL

Figure 17.

SIDE WALL	EE	PROTECTOR
	EE

B	H D FF
B	G

CC C

A B C D E F G

MODEL 21

19” 7"

8.5" 8"

16"

NOTE: All clearances are to combustibles with close clearance shields and pipe shield, DVL Close Clearance pipe with elbow, and minimum floor protector.

CEILING

DVL CLOSE

CLEARANCE

PIPE

Figure 18.

optional pipe shield.

NOTE:

See Page 33 for

installation of

optional close

clearance shields

and pipe shield

optional close clearance shield

SIDE WALL

LISTED 2100° UL 103 HT TYP.

CHIMNEY REEFER TO

MANUFACTURER’S INSTALLATION INSTRUCTION

LISTED 2100° UL 103 HT

TYP. CHIMNEY T-BOX

ASSEMBLY REEFER TO

MANUFACTURER’S

INSTALLATION

INSTRUCTION

WALL

PASS-THROUGH

CONNECTOR

Page 27

Image 27

New Buck Corporation installation instructions Listed 2100 UL HT T-Boxassembly

Contents

MODEL NON-CATALYTICUNIT MODEL NON-CATBuck Stove Page TABLE OF CONTENTS INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS MODELREAD THIS FIRST IMPORTANT INSTRUCTIONS INTRODUCTION SECTION MASONRY INSERT INSTALLATION SECTIONMODEL Floor Protection POSSIBLE TOOLS NEEDED FOR INSTALLATION INSTALLATION PREPARATIONMASONRY INSERT INSTALLATION OPTIONS FRONT OF STOVE UNIT WITH INSULATION OR HIGH AIRTIGHT INSU LATED CLEAN OUT REMOVE DAMPEROR WIRE IT OPEN STARTER PIPE SEAL TRIM PANELS AND UNDER FIGURE 3 MOUNTING TRIM PANELS POSITIONING THE HEATERPOSITIONING MOUNTING THE TRIM PANELS FINAL CHECK Page SECTION PRE-FABINSERT INSTALLATION Chimney PREPARING THE STOVE FOR INSTALLATION Floor Protection 1. Convert specification to R-value CHIMNEY HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential Installation PREPARING THE ROOM HEATER LOCATION Model 21 minimum clearance to combustibles HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential InstallationNOTE For minimum clearances See Page 17, Figure Model 21 minimum clearance to combustibles NOTE For minimum clearances See Page 19, Figure Residential and Mobile Home InstallationHOW TO LOCATE CHIMNEY EXIT, AND INSTALL Without close clearance shield and pipe shield Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationD. Vertical Wall Exit using 6 DVL Close Clearance Pipe, and Elbow, and any Listed 2100 UL HT chimney and Listed 2100 UL HT T-Boxassembly Model 21 minimum clearance to combustibles Listed 2100 UL HT T-Boxassembly HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationNOTE For minimum clearances See Page 23, Figure Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationNOTE For minimum clearances See Page 25, Figure Listed 2100 UL HT T-Boxassembly OUT SIDE AIR INSTALLATION Page FINAL CHECK SECTION ALCOVE INSTALLATION AND CLEARANCES PREPARING THE STOVE FOR INSTALLATIONChimney Floor Protection 1. Convert specification to R-value HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Alcove Installation ALCOVE INSTALLATION AND CLEARANCES any listed 2100 UL 103 HT. TYPE ChimneyModel 21 minimum clearance to combustibles 13/16” TYP 1” TYP 1/4” TYP Installation of Optional Close Clearance ShieldsInstallation of Optional Pipe Shield Pipe Shield Loosen these top shield screws FINAL CHECK SECTION WOOD HEATER SAFETY BUILDING A FIRE SECTION OPERATION POSSIBLE CAUSE SECTION TROUBLESHOOTINGPROBLEM SOLUTION PROBLEM SOLUTIONPOSSIBLE CAUSE PRODUCTS COVERED WARRANTY TIME PERIODSPROCEDURE NEW BUCK CORPORATION NBC OTHER RIGHTS CONDITIONS AND EXCLUSIONS