Alcove Installation And Clearances | New Buck Corporation 21

ALCOVE INSTALLATION

ALCOVE INSTALLATION

AND CLEARANCES

E. Vertical exit using (6" DVL Close Clearance pipe, and

any listed 2100° UL 103 HT. TYPE Chimney).

With optional close clearance shield, and pipe shield.

Model 21 minimum clearance to combustibles.

Figure 22.

Figure 23.

BACK WALL

BB GD FF

SIDE WALL	EE	PROTECTOR
	EE
	A

CONTEMPORARY CAP

LISTED 2100° UL 103 HT

TYP. CHIMNEY

CAULK

STORM COLLAR

H

G

FLASHING

RADIATION SHIELD

LISTED 2100° UL 103 HT TYP.

INSTALLATION

CEILING

C	SIDE
	WALL

CEILING SUPPORT

DVL CLOSE

CLEARANCE PIPE

BUCK STOVE

	A	B	C	D E
MODEL 21	19”	7"	84"	8.5" 8"

optional pipe shield.

NOTE:

See Page 33 for

installation of

optional close

clearance shields and pipe shield

F	G	H		optional close
3" 16"		48"		optional close
3" 16"		48"	BUCK STOVE	clearance shield
			NEW BUCK

NOTE: All clearances are to combustibles with optional close clearance shields, and pipe shield, using DVL Close Clearance pipe, and minimum floor protector.

32

Image 34

New Buck Corporation Alcove Installation And Clearances, any listed 2100 UL 103 HT. TYPE Chimney

Contents

MODEL NON-CAT MODEL NON-CATALYTICUNITBuck Stove Page TABLE OF CONTENTS MAINTENANCE INSTRUCTIONS MODEL INSTALLATION, OPERATION, ANDREAD THIS FIRST IMPORTANT INSTRUCTIONS SECTION INTRODUCTION SECTION MASONRY INSERT INSTALLATIONMODEL Floor Protection INSTALLATION PREPARATION POSSIBLE TOOLS NEEDED FOR INSTALLATIONMASONRY INSERT INSTALLATION OPTIONS STARTER PIPE SEAL TRIM PANELS AND UNDER AIRTIGHT INSU LATED CLEAN OUT REMOVE DAMPEROR WIRE IT OPEN FRONT OF STOVE UNIT WITH INSULATION OR HIGH MOUNTING THE TRIM PANELS POSITIONING THE HEATERPOSITIONING FIGURE 3 MOUNTING TRIM PANELS FINAL CHECK Page SECTION PRE-FABINSERT INSTALLATION PREPARING THE STOVE FOR INSTALLATION Chimney 1. Convert specification to R-value Floor Protection PREPARING THE ROOM HEATER LOCATION HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential Installation CHIMNEY Model 21 minimum clearance to combustibles Residential Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLNOTE For minimum clearances See Page 17, Figure Model 21 minimum clearance to combustibles Without close clearance shield and pipe shield Residential and Mobile Home InstallationHOW TO LOCATE CHIMNEY EXIT, AND INSTALL NOTE For minimum clearances See Page 19, Figure any listed 2100 UL 103 HT. TYPE Chimney Model 21 minimum clearance to combustibles Residential and Mobile Home Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLD. Vertical Wall Exit using 6 DVL Close Clearance Pipe, and Elbow, and any Listed 2100 UL HT chimney and Listed 2100 UL HT T-Boxassembly Listed 2100 UL HT T-Boxassembly Model 21 minimum clearance to combustibles Residential and Mobile Home Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLNOTE For minimum clearances See Page 23, Figure any listed 2100 UL 103 HT. TYPE Chimney Model 21 minimum clearance to combustibles Residential and Mobile Home Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLNOTE For minimum clearances See Page 25, Figure Listed 2100 UL HT T-Boxassembly OUT SIDE AIR INSTALLATION Page FINAL CHECK PREPARING THE STOVE FOR INSTALLATION SECTION ALCOVE INSTALLATION AND CLEARANCESChimney 1. Convert specification to R-value Floor Protection Alcove Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALL any listed 2100 UL 103 HT. TYPE Chimney ALCOVE INSTALLATION AND CLEARANCESModel 21 minimum clearance to combustibles Pipe Shield Loosen these top shield screws Installation of Optional Close Clearance ShieldsInstallation of Optional Pipe Shield 13/16” TYP 1” TYP 1/4” TYP FINAL CHECK SECTION WOOD HEATER SAFETY SECTION OPERATION BUILDING A FIRE SOLUTION SECTION TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE SOLUTION PROBLEMPOSSIBLE CAUSE NEW BUCK CORPORATION NBC WARRANTY TIME PERIODSPROCEDURE PRODUCTS COVERED CONDITIONS AND EXCLUSIONS OTHER RIGHTS