New Buck Corporation 21 guide

14.From under the mobile home, slip the duct up through the 4-1/4" hole. Push up until the face of the outside air duct contacts the underside of the floor of the mobile home. For certain floor thickness, you may have to shorten the length of the outside air duct.

15.Secure the outside air duct to the floor using the four (4) #10x1 screws provided. (See Figure 19.)

RAINCAP

RAIN CAP

24" min.(610mm)

36" TYP36"..

FLASHING

RADIATIONON SH ELD

SHIELD

20 FT. MAX.

20 ft. MAX

24" in.
24" min.(610mm)	36" 36"TYP. .
(610 mm)	36" 36"TYP. .
	FLASHING
	RADIATIONTION SHIELD
	SHIELD

OUT SIDE AIR DUCT THROUGH FLOOR WHEN		OUT SIDE AIR DUCT THROUGH FLOOR WHEN
TSIDE AIR DUCT TH OUGH FLOOR WHEN
MOBLE HOME IS NOT UNDERPENNED		OUTSIDE A R DUCT THROUGH UNDERPE
MOBILE HOME IS NOT UNDERPINNED		OUTSIDE A R DUCT THROUGH UNDERPE
MOBILE HOME IS NOT UNDERPINNED		MOBILE HOME IS UNDERPINNED

Figure 19

Page 29

Image 29

New Buck Corporation 21 installation instructions

Contents

Buck Stove MODEL NON-CATALYTICUNITMODEL NON-CAT Page TABLE OF CONTENTS READ THIS FIRST IMPORTANT INSTRUCTIONS INSTALLATION, OPERATION, ANDMAINTENANCE INSTRUCTIONS MODEL INTRODUCTION SECTION MODEL MASONRY INSERT INSTALLATIONSECTION Floor Protection MASONRY INSERT INSTALLATION OPTIONS POSSIBLE TOOLS NEEDED FOR INSTALLATIONINSTALLATION PREPARATION OR WIRE IT OPEN AIRTIGHT INSU LATED CLEAN OUT REMOVE DAMPERSTARTER PIPE SEAL TRIM PANELS AND UNDER FRONT OF STOVE UNIT WITH INSULATION OR HIGH POSITIONING POSITIONING THE HEATERMOUNTING THE TRIM PANELS FIGURE 3 MOUNTING TRIM PANELS FINAL CHECK Page SECTION PRE-FABINSERT INSTALLATION Chimney PREPARING THE STOVE FOR INSTALLATION Floor Protection 1. Convert specification to R-value Residential Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLPREPARING THE ROOM HEATER LOCATION CHIMNEY Model 21 minimum clearance to combustibles NOTE For minimum clearances See Page 17, Figure HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential Installation Model 21 minimum clearance to combustibles HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationWithout close clearance shield and pipe shield NOTE For minimum clearances See Page 19, Figure Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney D. Vertical Wall Exit using 6 DVL Close Clearance Pipe, and Elbow, and any Listed 2100 UL HT chimney and Listed 2100 UL HT T-Boxassembly HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential and Mobile Home Installation Model 21 minimum clearance to combustibles Listed 2100 UL HT T-Boxassembly NOTE For minimum clearances See Page 23, Figure HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential and Mobile Home Installation Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney NOTE For minimum clearances See Page 25, Figure HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential and Mobile Home Installation Listed 2100 UL HT T-Boxassembly OUT SIDE AIR INSTALLATION Page FINAL CHECK Chimney SECTION ALCOVE INSTALLATION AND CLEARANCESPREPARING THE STOVE FOR INSTALLATION Floor Protection 1. Convert specification to R-value HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Alcove Installation Model 21 minimum clearance to combustibles ALCOVE INSTALLATION AND CLEARANCESany listed 2100 UL 103 HT. TYPE Chimney Installation of Optional Pipe Shield Installation of Optional Close Clearance ShieldsPipe Shield Loosen these top shield screws 13/16” TYP 1” TYP 1/4” TYP FINAL CHECK SECTION WOOD HEATER SAFETY BUILDING A FIRE SECTION OPERATION PROBLEM SECTION TROUBLESHOOTINGSOLUTION POSSIBLE CAUSE POSSIBLE CAUSE PROBLEMSOLUTION PROCEDURE WARRANTY TIME PERIODSNEW BUCK CORPORATION NBC PRODUCTS COVERED OTHER RIGHTS CONDITIONS AND EXCLUSIONS