New Buck Corporation 21 specification

Model 21 minimum clearance to combustibles.

A. Vertical exit using (6" Single Wall minimum 24 ga. blued or black

pipe, and any listed 2100° UL 103 HT. TYPE Chimney). Without optional close clearance shield, and pipe shield.

Model 21 minimum clearance to combustibles.

Figure 7.

Figure 8.

		BACK WALL			CONTEMPORARY CAP
					CONTEMPORARY CAP
		B	D FF	LISTED 2100° UL 103 HT
		B	G	LISTED 2100° UL 103 HT
WALLSIDE				TYP. CHIMNEY
		PROTECTOR			CAULK
		PROTECTOR			STORM COLLAR
					STORM COLLAR
	EE			G	FLASHING
	A			RADIATION SHIELD	FLASHING
	A

				LISTED 2100° UL 103 HT TYP.
				INSTALLATION
				CEILING	CEILING SUPPORT
				CEILING
					SINGLE WALL
					CONNECTOR PIPE
	CC		C	SIDE
	CC		C	WALL

	A	B	C	D	E	F	G
MODEL 21	25”	13" 19" 15.5" 8"				3"	16"	NEW BUCK
								BUCK STOVE

NOTE: All clearances are to combustibles without close clearance shields, and pipe shield, using 6" Single Wall minimum 24 ga. blued or black pipe , and minimum floor protector . The clearances above may be reduced. Follow NFPA-211codes if available or follow instructions on (Pages 18, and 19, or Pages 22, and 23).

15

Image 17

New Buck Corporation installation instructions Model 21 minimum clearance to combustibles

Contents

Buck Stove MODEL NON-CATALYTICUNITMODEL NON-CAT Page TABLE OF CONTENTS READ THIS FIRST IMPORTANT INSTRUCTIONS INSTALLATION, OPERATION, ANDMAINTENANCE INSTRUCTIONS MODEL INTRODUCTION SECTION MODEL MASONRY INSERT INSTALLATIONSECTION Floor Protection MASONRY INSERT INSTALLATION OPTIONS POSSIBLE TOOLS NEEDED FOR INSTALLATIONINSTALLATION PREPARATION OR WIRE IT OPEN AIRTIGHT INSU LATED CLEAN OUT REMOVE DAMPERSTARTER PIPE SEAL TRIM PANELS AND UNDER FRONT OF STOVE UNIT WITH INSULATION OR HIGH POSITIONING POSITIONING THE HEATERMOUNTING THE TRIM PANELS FIGURE 3 MOUNTING TRIM PANELS FINAL CHECK Page SECTION PRE-FABINSERT INSTALLATION Chimney PREPARING THE STOVE FOR INSTALLATION Floor Protection 1. Convert specification to R-value Residential Installation HOW TO LOCATE CHIMNEY EXIT, AND INSTALLPREPARING THE ROOM HEATER LOCATION CHIMNEY Model 21 minimum clearance to combustibles NOTE For minimum clearances See Page 17, Figure HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential Installation Model 21 minimum clearance to combustibles HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Residential and Mobile Home InstallationWithout close clearance shield and pipe shield NOTE For minimum clearances See Page 19, Figure Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney D. Vertical Wall Exit using 6 DVL Close Clearance Pipe, and Elbow, and any Listed 2100 UL HT chimney and Listed 2100 UL HT T-Boxassembly HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential and Mobile Home Installation Model 21 minimum clearance to combustibles Listed 2100 UL HT T-Boxassembly NOTE For minimum clearances See Page 23, Figure HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential and Mobile Home Installation Model 21 minimum clearance to combustibles any listed 2100 UL 103 HT. TYPE Chimney NOTE For minimum clearances See Page 25, Figure HOW TO LOCATE CHIMNEY EXIT, AND INSTALLResidential and Mobile Home Installation Listed 2100 UL HT T-Boxassembly OUT SIDE AIR INSTALLATION Page FINAL CHECK Chimney SECTION ALCOVE INSTALLATION AND CLEARANCESPREPARING THE STOVE FOR INSTALLATION Floor Protection 1. Convert specification to R-value HOW TO LOCATE CHIMNEY EXIT, AND INSTALL Alcove Installation Model 21 minimum clearance to combustibles ALCOVE INSTALLATION AND CLEARANCESany listed 2100 UL 103 HT. TYPE Chimney Installation of Optional Pipe Shield Installation of Optional Close Clearance ShieldsPipe Shield Loosen these top shield screws 13/16” TYP 1” TYP 1/4” TYP FINAL CHECK SECTION WOOD HEATER SAFETY BUILDING A FIRE SECTION OPERATION PROBLEM SECTION TROUBLESHOOTINGSOLUTION POSSIBLE CAUSE POSSIBLE CAUSE PROBLEMSOLUTION PROCEDURE WARRANTY TIME PERIODSNEW BUCK CORPORATION NBC PRODUCTS COVERED OTHER RIGHTS CONDITIONS AND EXCLUSIONS