NXP Semiconductors UM10310 9.3 Basic timer operation

UM10310_1 © NXP B.V. 2008. All rights reserved.

User manual Rev. 01 — 1 December 2008 48 of 139

NXP Semiconductors UM10310

P89LPC9321 User manual

9.3 Basic timer operation

The Timer is a free-running up/down counter counting at the pace determined by the

prescaler. The timer is started by setting the CCU Mode Select bits TMOD21 and

TMOD20 in the CCU Control Register 0 (TCR20) as shown in the table in the TCR20

register description (Tabl e 37).

The CCU direction control bit, TDIR2, determines the direction of the count. TDIR2 = 0:

Count up, TDIR2 = 1: Count down. If the timer counting direction is changed while the

counter is running, the count sequence will be reversed in the CCUCLK cycle following

the write of TDIR2. The timer can be written or read at any time and newly-written values

will take effect when the prescaler overflows. The timer is accessible through two SFRs,

TL2(low byte) and TH2(high byte). A third 16-bit SFR, TOR2H:TOR2L, determines the

overflow reload value. TL2, TH2 and TOR2H, TOR2L will be 0 after a reset

Up-counting: When the timer contents are FFFFH, the next CCUCLK cycle will set the

counter value to the contents of TOR2H:TOR2L.

Down-counting: When the timer contents are 0000H, the next CCUCLK cycle will set the

counter value to the contents of TOR2H:TOR2L. During the CCUCLK cycle when the

reload is performed, the CCU Timer Overflow Interrupt Flag (TOIF2) in the CCU Interrupt

Flag Register (TIFR2) will be set, and, if the EA bit in the IEN0 register and ECCU bit in

the IEN1 register (IEN1.4) are set, program execution will vector to the overflow interrupt.

The user has to clear the interrupt flag in software by writing a logic0 to it.

When writing to the reload registers, TOR2H and TOR2L, the values written are stored in

two 8-bit shadow registers. In order to latch the contents of the shadow registers into

TOR2H and TOR2L, the user must write a logic 1 to the CCU Timer Compare/Overflow

Update bit TCOU2, in CCU Timer Control Register 1 (TCR21). The function of this bit

Fig 21. Capture Compare Unit block diagram.

16-BIT SHADOW REGISTER

TOR2H TO TOR2L 16-BIT SHADOW REGISTER

OCRxH TO OCRxL

16-BIT CAPTURE

REGISTER ICRxH, L

INTERRUPT FLAG

TICF2x SET

EVENT

COUNTER

NOISE

FILTER

ICNFx

EDGE

SELECT

ICESx

16-BIT COMPARE

VALUE

TIMER > COMPARE

16-BIT TIMER RELOAD

REGISTER

16-BIT UP/DOWN TIMER

WITH RELOAD

FCOx

OCA

ICA

ICB

OCB

OVERFLOW/

UNDERFLOW

OCC

OCD

COMPARE CHANNELS A TO D

CAPTURE CHANNELS A, B

002aab009

10-BIT DIVIDER

32 × PLL

4-BIT

DIVIDER

Contents

Main Contact information User manual Rev. 01 1 December 2008 3 of 139 NXP Semiconductors UM10310 P89LPC9321 User manual 1. Introduction 1.1 Pin configuration Fig 1. TSSOP28 pin configuration P89LPC9321FDH Fig 2. PLCC28 pin configuration Fig 3. DIP28 pin configuration P89LPC9321FA P89LPC9321FN 1.2 Pin description Page Page User manual Rev. 01 1 December 2008 8 of 139 P89LPC9321 User manual 1.3 Functional diagram P89LPC9321 Fig 4. Functional diagram User manual Rev. 01 1 December 2008 9 of 139 P89LPC9321 User manual 1.4 Block diagram Fig 5. Block diagram P89LPC9321 Page Page Page Page Page Page Page Page Page Page User manual Rev. 01 1 December 2008 20 of 139 1.6 Memory organization Fig 6. P89LPC9321 memory map 2. Clocks 2.1 Enhanced CPU 2.2 Clock definitions 2.2.1 Oscillator Clock (OSCCLK) 2.3 External crystal oscillator option 2.4 Clock output 2.5 On-chip RC oscillator option 2.6 Watchdog oscillator option 2.7 External clock input option 2.8 Clock sources switch on the fly 2.9 Oscillator Clock (OSCCLK) wake-up delay 2.10 CPU Clock (CCLK) modification: DIVM register 2.11 Low power select 3. Interrupts 3.1 Interrupt priority structure 3.2 External Interrupt pin glitch suppression 4. I/O ports 4.1 Port configurations 4.2 Quasi-bidirectional output configuration 4.3 Open drain output configuration NXP Semiconductors UM10310 4.4 Input-only configuration 4.5 Push-pull output configuration 4.6 Port 0 and Analog Comparator functions 4.7 Additional port features 5. Power monitoring functions 5.1 Brownout detection 5.2 Power-on detection 5.3 Power reduction modes 6. Reset 6.1 Reset vector 7. Timers 0 and 1 7.1 Mode 0 7.2 Mode 1 7.3 Mode 2 7.4 Mode 3 7.5 Mode 6 Fig 15. Timer/counter 0 or 1 in Mode 0 (13-bit counter). Fig 16. Timer/counter 0 or 1 in mode 1 (16-bit counter). Fig 17. Timer/counter 0 or 1 in Mode 2 (8-bit auto-reload). 7.6 Timer overflow toggle output 8. Real-time clock system timer Fig 18. Timer/counter 0 Mode 3 (two 8-bit counters). Fig 19. Timer/counter 0 or 1 in mode 6 (PWM auto-reload). 8.1 Real-time clock source 8.2 Changing RTCS1/RTCS0 8.3 Real-time clock interrupt/wake-up 8.3.1 Real-time clock read back 8.4 Reset sources affecting the Real-time clock Page 9. Capture/Compare Unit (CCU) 9.3 Basic timer operation Page 9.4 Output compare 9.5 Input capture 9.6 PWM operation 9.7 Alternating output mode 9.8 Synchronized PWM register update 9.9 HALT 9.10 PLL operation Page Page Page 10. UART 10.1 Mode 0 10.2 Mode 1 10.3 Mode 2 10.4 Mode 3 10.5 SFR space 10.6 Baud Rate generator and selection 10.7 Updating the BRGR1 and BRGR0 SFRs 10.8 Framing error 10.9 Break detect Page 10.10 More about UART Mode 0 10.11 More about UART Mode 1 10.12 More about UART Modes 2 and 3 Fig 29. Serial Port Mode 2 or 3 (only single transmit buffering case is shown) If SM2 = 1 in modes 2 and 3, RI and FE behaves as in the following table. 10.13 Framing error and RI in Modes 2 and 3 with SM2 = 1 Fig 28. Serial Port Mode 1 (only single transmit buffering case is shown) 10.14 Break detect 10.15 Double buffering 10.16 Double buffering in different modes 10.17 Transmit interrupts with double buffering enabled (Modes 1, 2, and 3) 10.18 The 9th bit (bit 8) in double buffering (Modes 1, 2, and 3) 10.19 Multiprocessor communications 10.20 Automatic address recognition 11. I2C interface 11.1 I2C data register 11.2 I2C slave address register 11.3 I2C control register 11.4 I2C Status register 11.5 I2C SCL duty cycle registers I2SCLH and I2SCLL 11.6 I2C operation modes 11.6.1 Master Transmitter mode 11.6.2 Master Receiver mode 11.6.3 Slave Receiver mode 11.6.4 Slave Transmitter mode Fig 37. I2C serial interface block diagram. Page Page Page Page Page 12. Serial Peripheral Interface (SPI) Page Page Fig 39. SPI single master single slave configuration. Fig 40. SPI dual device configuration, where either can be a master or a slave. 12.1 Configuring the SPI 12.2 Additional considerations for a slave 12.3 Additional considerations for a master 12.4 Mode change on SS 12.5 Write collision 12.6 Data mode Fig 42. SPI slave transfer format with CPHA = 0. Fig 43. SPI slave transfer format with CPHA = 1. P89LPC9321 User manual Fig 44. SPI master transfer format with CPHA = 0. 12.7 SPI clock prescaler select 13. Analog comparators 13.1 Comparator configuration Page 13.2 Internal reference voltage 13.3 Comparator input pins 13.4 Comparator interrupt 13.5 Comparators and power reduction modes 13.6 Comparators configuration example 13.7 Programmable Gain Amplifier (PGA) Page 14. Keypad interrupt (KBI) 15. Watchdog timer (WDT) 15.1 Watchdog function 15.2 Feed sequence NXP Semiconductors UM10310 (3) Tabl e 99 shows sample P89LPC9321 timeout values. tclks 2 ()255 1+()1 1048577=+= 15.3 Watchdog clock source 15.4 Watchdog Timer in Timer mode 15.5 Power-down operation 15.6 Periodic wake-up from power-down without an external oscillator 16. Additional features 16.1 Software reset 16.2 Dual Data Pointers 17. Data EEPROM 17.1 Data EEPROM read 17.2 Data EEPROM write 17.3 Hardware reset 17.4 Multiple writes to the DEEDAT register 17.5 Sequences of writes to DEECON and DEEDAT registers 17.6 Data EEPROM Row Fill 17.7 Data EEPROM Block Fill 18. Flash memory 18.1 General description 18.2 Features Page Page Page 18.5 In-circuit programming (ICP) 18.6 ISP and IAP capabilities of the P89LPC9321 18.7 Boot ROM 18.8 Power on reset code execution 18.9 Hardware activation of Boot Loader 18.10 In-system programming (ISP) 18.11 Using the In-system programming (ISP) Page Page 18.12 In-application programming (IAP) 18.13 IAP authorization key 18.14 Flash write enable 18.15 Configuration byte protection 18.16 IAP error status Page Page Page 18.17 User configuration bytes 18.18 User security bytes This device has three security bits associated with each of its eight sectors, as shown in Table116 18.19 Boot Vector register 18.20 Boot status register Page 19. Instruction set Page Page 20. Legal information 20.1 Definitions 20.2 Disclaimers 20.3 Trademarks 21. Tables Page 22. Figures 23. Contents