Manuals / Omega Engineering / Kitchen Appliance / Slow Cooker

Omega Engineering 30, 48, 20, 25 to insert, 10.0ºC, To add a new stage before an existing one

Models: 25 30 20 48

1 37

Download 37 pages 33.35 Kb

Page 22

Image 22

To add a new stage before an existing one

Use the “Up Arrow” or “Down Arrow” keys to highlight the stage number.

Press "Enter"

A new stage will be added before the existing stage. The other stage numbers will be adjusted as appropriate. The new stage can now be edited as described above.

To add a new stage at the end

- - - - - - - - - - -

FinPostextnru 72.0ºC		5m00
FinPosthold		10.0ºC
[	to insert	stage ]

Use the “Up Arrow” or “Down Arrow” keys to highlight the dotted line below the last stage.

Press "Enter"

A new stage will be added with the next consecutive number. The new stage can now be edited as described above.

To delete a stage

Use the “Up Arrow” or “Down Arrow” keys to highlight the stage you wish to delete.

Press "Delete"

The prompt line will flash between 'DEL

STAGE?' and 'YES’ or ‘NO'.

Press “Enter”

to delete the stage.

Page 22

Image 22

Omega Engineering 30, 48 to insert, 10.0ºC, To add a new stage before an existing one, To add a new stage at the end

Contents

User’sGuide TCY 20, 25, 30Thermal Cyclers Shop online atServicing North America OMEGAnet Online Service omega.comInternet e-mail info@omega.com For immediate technical or application assistanceContents 1. Introduction 2. Safety and installationOperator Safety Unpacking InstallationReplacement cable ELECTRICIANWorking Conditions Heating/Cooling Rate 3. Cycler TCY SpecificationTemperature Heated LidPower 4. User operation and consumablesDimensions Heated lid0.5ml Tubes to select TCYTCProgramsMethods00 Information ConfigurationPrograms Configuration5. Front panel controls MethodsThe Up arrow key The keysThe End, Finish or Exit key The Down arrow keyThe Decimal Point and Insert key 6. Programming the CYCLERThe Down arrow key The Delete keyStage MethodsPrograms00 Information Configurationto select CycleRun ProgramMethod 2 STEP TEMPLATESTEP Option 1 Creating programs using templatesTo give a program a name To save the programto select DONNA 7 Run programmethod ProgramsMethods00 Information ConfigurationSet password to select To edit a field or step in an existing program72.0ºC Post hold10.0 5m00To set a password for a selected program UNNAMED #10.0ºCºC 105ºCProgramming to selectExample programs New*New- program ** 2 STEP TEMPLATE 5012 3 STEP TEMPLATEto edit the step as To insert additional stepsTo delete a step described abovestage to insert10.0ºC To add a new stage before an existing oneTo insert a ‘pause’ into a program The prompt line will flash between ‘CHANGE TO PAUSE?’ and ‘YES or NO’Press “Enter” Press “Pause” To program increment or decrement temperature or timeTemperature profile of incremented Hold Time at step 3 of each cycle to go into edit modetwice to go into edit View methodProgram Run ProgrammethodGEORGE to selectNewprogramMethods Run methodProgramto select to selectHold @ Sample58.0ºC 72.0ºCBlock s/nid 8. Configuration7. Information Unit s/nPasswordsFormat memory ProgramSettingsdefaultsxxxx SettingsSURE ? Thiswill delete Passwords9. Notes on transferring protocols from other thermal cyclers Heater Block removal 10. User maintenanceCleaning your CYCLER Underside of the CYCLER TCY11. Some frequently asked questions Insulation testing 12. Additional informationFault Finding FusesWARRANTY/DISCLAIMER RETURN REQUESTS/INQUIRIESFLOW/LEVEL TEMPERATUREPRESSURE, STRAIN AND FORCE pH/CONDUCTIVITY

To add a new stage before an existing one

To add a new stage at the end

to insert

stage ]

To delete a stage