Manuals / Omega Engineering / Kitchen Appliance / Slow Cooker

Omega Engineering 25, 48, 20 Front panel controls, Programs, Methods, Information, Configuration

Models: 25 30 20 48

1 37

Download 37 pages 33.35 Kb

Page 11

Image 11

5.Front panel controls

The LCD Display

Programs				[0]		The CYCLER TCY has a four line LCD
						display. The top three lines are
Methods			[0]			information or program lines, while the
Information
Configuration						bottom line is a prompt line. The active
					]	line flashes on screen and is shown in
[	,	to select		]		bold in this manual.
	,	to select

The bottom line may change or flash between two or three different prompts depending upon which program line is active. An example of a prompt line which flashes between three different prompts is shown here.

Indicators

Power: This indicator is lit when there is power to the CYCLER TCY.

Status: This indicator is lit when the CYCLER TCY is running a program. It is off when the unit is stopped. It will flash and beep slowly when the unit is paused. It will flash after a five second quick sequence of beeps when the unit reaches its final hold temperature.

Page 11

Image 11

Omega Engineering 25, 48 Front panel controls, Programs, Methods, Information, Configuration, to select, The LCD Display

Contents

Shop online at TCY 20, 25, 30Thermal Cyclers User’sGuideFor immediate technical or application assistance OMEGAnet Online Service omega.comInternet e-mail info@omega.com Servicing North AmericaContents Operator Safety 2. Safety and installation1. Introduction ELECTRICIAN InstallationReplacement cable UnpackingWorking Conditions Heated Lid 3. Cycler TCY SpecificationTemperature Heating/Cooling RateHeated lid 4. User operation and consumablesDimensions Power0.5ml Tubes Information Configuration TCYTCProgramsMethods00 to selectMethods Configuration5. Front panel controls ProgramsThe Down arrow key The keysThe End, Finish or Exit key The Up arrow keyThe Delete key 6. Programming the CYCLERThe Down arrow key The Decimal Point and Insert keyCycle MethodsPrograms00 Information Configurationto select StageOption 1 Creating programs using templates 2 STEP TEMPLATESTEP Run ProgramMethodTo save the program To give a program a nameTo edit a field or step in an existing program ProgramsMethods00 Information ConfigurationSet password to select to select DONNA 7 Run programmethod5m00 Post hold10.0 72.0ºC105ºC UNNAMED #10.0ºCºC To set a password for a selected programNew*New- program ** 2 STEP TEMPLATE 5012 3 STEP TEMPLATE to selectExample programs Programmingdescribed above To insert additional stepsTo delete a step to edit the step asTo add a new stage before an existing one to insert10.0ºC stageThe prompt line will flash between ‘CHANGE TO PAUSE?’ and ‘YES or NO’ To insert a ‘pause’ into a programPress “Enter” Press “Pause” To program increment or decrement temperature or timeTemperature profile of incremented Hold Time at step 3 of each cycle to go into edit modetwice to go into edit to select Run ProgrammethodGEORGE View methodProgramto select Run methodProgramto select NewprogramMethods72.0ºC Sample58.0ºC Hold @Unit s/n 8. Configuration7. Information Block s/nidSettings ProgramSettingsdefaultsxxxx PasswordsFormat memoryPasswords Thiswill delete SURE ?9. Notes on transferring protocols from other thermal cyclers Underside of the CYCLER TCY 10. User maintenanceCleaning your CYCLER Heater Block removal11. Some frequently asked questions Insulation testing 12. Additional informationFault Finding The heated lid over-temperature cut-outRETURN REQUESTS/INQUIRIES WARRANTY/DISCLAIMERpH/CONDUCTIVITY TEMPERATUREPRESSURE, STRAIN AND FORCE FLOW/LEVEL