Onkyo TX-L55 instruction manual Using the Listening Modes-Continued, Dolby Digital/DTS Setting

TX-L55_En.book Page 43 Tuesday, June 1, 2004 9:02 AM

Using the Listening Modes—Continued

Dolby Digital/DTS Setting

(5.1- or 6.1-channel Playback)

This setting determines if Dolby Digital and DTS mate- rial is played using 6.1-channels or 5.1-channels. This setting only applies when you’re using a surround back speaker, the Speaker Configuration Surr Back setting is set to something other than Non (page 48), and the sur- round information in the current digital input signal is 3/

2.1or 3/3.1. To check the format of a digital input signal, see “Displaying Source Information” on page 46.

ON STANDBY

TV

I INPUT

	1		2	3		+
						TV CH
	4		5	6		-
	7		8	9
						TV VOL
	+10		0	CLEAR
	--/---					REMOTE
	TONE
		_				MODE	AMP
				+		TUNER
						AMP
	DVD	V1		V2		DVD
	INPUT SELECTOR
	TV	AUX		TUN		TV
	DIMMER					SLEEP
	TV		U	MEN
ENTER		PMEN			U
	INPUT	TO
	+
	CH		ENTER			VOL
	DISC
	-	EXIT		GUIDE
	PREV	R		TUP
		ET	URN
	CH			SE
	DISPLAY					MUTING	SETUP
	PLAY MODE	SP A		SP B		RANDOM
	AUDIO	SUBTITLE		ANGLE		LAST M
	DIRECT	STEREO		SURR		DSP
	REPEAT	A-B		SEARCH		MEMORY
	TUN -	TUN +		TUN M		P MEM
				LEVEL		LEVEL
	TEST TONE	CH SEL		-		+
	OPEN/CLOSE	VIDEO OFF
				L.NIGHT		CINE FLTR
			RC-577S

1		Press the REMOTE MODE [AMP]
	AMP	button followed by the [SETUP]

TUNER button.

2	Use the Up and Down [ ]/[ ]
	buttons to select “5. Audio Adj,”
ENTER	and then press [ENTER].

ENTER

3		Use the Up and Down [ ]/[	]
		buttons to select “Surr Bk,” and
	ENTER	then use the Left and Right [	]/

[ ] buttons to select Auto, On, or Off.

4	Press the [SETUP] button.
	The setup menu closes.

This setting affects Dolby Digital and DTS sources as follows:

Dolby Digital

Auto: If the source signal contains a Dolby Digital EX flag, Dolby Digital EX 6.1 is used. If not, Dolby Digital 5.1 is used.

On: Dolby Digital EX 6.1 is used regardless of whether the source signal contains a Dolby Digital EX flag. You can choose Dolby Digital EX or PL IIx Music mode with the [SURR] button.

Off: Dolby Digital 5.1 is used even if a Dolby Dig- ital EX flag is present.

DTS

Auto: If the source signal contains a DTS-ES flag, DTS-ES Discrete (6.1) or DTS-ES Matrix (6.1) is selected automatically. If not, DTS 5.1 is used.

On: DTS-ES 6.1 is used regardless of whether the source signal contains a DTS-ES flag. If the source signal contains a DTS-ES flag, DTS-ES Discrete (6.1) or DTS-ES Matrix (6.1) is selected automatically. If the source signal does not contain a DTS-ES flag, you can choose DTS+Dolby EX, PL IIx Music, or DTS+Neo:6 with the [SURR] button.

Off: DTS 5.1 is used for all DTS sources, even if a DTS-ES flag is present.

43