To use the same volume level as when the AV receiver was last turned off, select “Last”.

The “Zone2 Power On Volume” and “Zone3 Power On Volume” cannot be set higher than the “Zone2 Maximum Volume” and “Zone3 Maximum Volume” setting.

Using Zone 2/3

This section explains how to turn Zone 2/3 on and off, how to select an input source for Zone 2/3, and how to adjust the volume for Zone 2/3.

Controlling Zone 2/3 from the AV receiver

ZONE 3 indicator

ZONE 2 indicator

ZONE 3

Input selector buttons

 

ZONE 2

OFF

 

1 To turn on Zone 2/3 and select an input source,

press ZONE 2 or ZONE 3 followed by an input selector button within 8 seconds.

Zone 2/3 turns on, the ZONE 2/3 indicator lights.

Tip

ZONE 2/3 12V TRIGGER OUT goes high (+12 V).

To select AM or FM, press TUNER input selector and ZONE 2 or ZONE 3 repeatedly.

(North American models) You can also select SIR-

IUS.

To select the same source as that of the main room, press ZONE 2 or ZONE 3 twice. “Zone 2 Selector:

Source” or “Zone 3 Selector: Source” appears on

the display.

2 To turn off Zone 2/3, press ZONE 2 or ZONE 3.

ZONE 2 or ZONE 3 indicator flashes.

Press OFF.

The zone is turned off, and the ZONE 2 or ZONE 3 indicator goes off.

Note

When Zone 2/3 is turned off, the output from the ZONE 2/3 12V TRIGGER OUT goes low (0 volts).

Controlling Zone 2/3 with the Remote Controller

STANDBY

 

 

 

 

 

ON

 

 

 

 

ZONE

 

 

 

INPUT

 

 

 

 

 

 

 

 

 

 

SELECTOR

 

 

 

 

 

Note

To control Zone 2/3, you must press the remote controller’s ZONE first.

ZONE turns red while Zone 2 is on, and green while Zone 3 is on.

1 Press ZONE repeatedly, then point the remote controller at the AV receiver and press ON.

Tip

The ZONE 2/3 12V TRIGGER OUT goes high (+12 V).

 

 

2

To select an input source for Zone 2/3, press

 

ZONE repeatedly, followed by INPUT SELEC-

 

TOR.

 

To select AM or FM, press TUNER input selector

 

and ZONE repeatedly.

 

(North American models) You can also select SIR-

 

IUS.

 

 

3

To turn off Zone 2/3, press ZONE repeatedly, fol-

 

lowed by STANDBY.

Note

Only analog input sources are output by the ZONE 2/3 PRE OUT and FRONT WIDE/ZONE 2 L/R, FRONT HIGH/ZONE 3 L/R terminals. Digital input sources are not output. If no sound is heard when an input source is selected, check if it’s connected to an analog input.

You cannot select different AM or FM radio stations for your main room and Zone 2/3. The same AM/FM radio station will be heard in each room. For example, if you have an FM station for the main room, that station will also be used in Zone 2.

When you connect ZONE3 speakers directly to the AV receiver, Dolby Pro Logic IIz Height listening mode that require front high speakers is unavailable.

When the input selector of Zone 2/3 is selected, power consump- tion on standby mode slightly increases.

While Zone 2/3 is on, ufunctions will not work.

En

76

Page 76
Image 76
Onkyo TX-NR1008 Using Zone 2/3, Controlling Zone 2/3 from the AV receiver, Controlling Zone 2/3 with the Remote Controller