Video

There’s no picture

Make sure that all video connecting plugs are pushed

17

in all the way.

 

 

 

Make sure that each video component is properly

18, 19,

connected.

80

If your TV is connected to the HDMI output, set the

43, 45

Monitor Out” setting other than “Analog”, and

 

select “- - - - - in the “HDMI Input” to watch com-

 

posite video, S-Video, and component video sources.

 

 

 

If your TV is connected to the COMPONENT

43, 45

VIDEO MONITOR OUT, MONITOR OUT S, or

 

MONITOR OUT V, set the “Monitor Out” setting

 

to “Analog”, and select “- - - - - in the “Component

 

Video Input” to watch composite video and S-Video

 

sources.

 

If the video source is connected to a component

19, 45

video input, you must assign that input to an input

 

selector, and your TV must be connected to either

 

the HDMI output or COMPONENT VIDEO MON-

 

ITOR OUT.

 

 

 

If the video source is connected to a composite video

19

input, your TV must be connected to the HDMI out-

 

put or the corresponding composite video output.

 

If the video source is connected to an HDMI input,

18, 45

you must assign that input to an input selector, and

 

your TV must be connected to the HDMI output.

 

While the Pure Audio listening mode is selected, the — video circuitry is turned off and only video signals input through HDMI IN can be output.

On your TV, make sure that the video input to which — the AV receiver is connected is selected.

There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is

99

not guaranteed. In addition, video signals from a PC

 

are not guaranteed.

 

 

 

When the “Monitor Out” setting is set to “Analog”,

44

and the “Resolution” setting is set to anything other

 

than “Through”, no video is output by the HDMI

 

outputs.

 

When the “Resolution” is set to any resolution not

44

supported by the TV, no video is output by the

 

HDMI outputs.

 

 

 

If the message “Resolution Error” appears on the

AV receiver’s display, this indicates that your TV

 

does not support the current video resolution and

 

you need to select another resolution on your DVD

 

player.

 

 

 

The on-screen menus don’t appear

(European and Asian models) Specify the TV sys-

57

tem used in your area in the “TV Format”.

 

 

On your TV, make sure that the video input to which —

the AV receiver is connected is selected.

 

If your TV is connected to the analog outputs, set the

43

Monitor Out” setting to “Analog”.

 

The picture is distorted

(European and Asian models) Specify the TV sys- 57 tem used in your area in the “TV Format”.

En

94

The on screen display does not appear

Depending on the input signal, the on screen display 57 may not appear when the input signal from the

HDMI IN is output to a device connected to the HDMI output.

Tuner

Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.

Move the AV receiver away from your TV or com-

puter.

 

Listen to the station in mono.

32

 

 

When listening to an AM station, operating the

remote controller may cause noise.

 

Passing cars and airplanes can cause interference.

 

 

Concrete walls weaken radio signals.

If nothing improves the reception, install an outdoor

antenna.

 

Remote Controller

The remote controller doesn’t work

Before operating this unit, be sure to press

RECEIVER.

 

 

 

Make sure that the batteries are installed with the

4

correct polarity.

 

Install new batteries. Don’t mix different types of

4

batteries, or old and new batteries.

 

 

 

Make sure that the remote controller is not too far

4

away from the AV receiver, and that there’s no

 

obstruction between the remote controller and the

 

AV receiver’s remote control sensor.

 

Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

 

Relocate if necessary.

 

 

 

If the AV receiver is installed in a rack or cabinet

with colored-glass doors, the remote controller may

 

not work reliably when the doors are closed.

 

Make sure you’ve selected the correct remote con-

11, 87

troller mode.

 

 

 

When using the remote controller to control other

manufacturers’ AV components, some buttons may

 

not work as expected.

 

Make sure you’ve entered the correct remote control

86

code.

 

 

 

Make sure to set the same ID on both the AV receiver

57

and remote controller.

 

 

 

Can’t control other components

If it’s an Onkyo component, make sure that the u

20

cable and analog audio cable are connected properly.

 

Connecting only an ucable won’t work.

 

 

 

Make sure you’ve selected the correct remote con-

11, 87

troller mode.

 

If you’ve connected a cassette tape deck, to the TV/

27

CD IN jack, or an RI Dock to the TV/CD IN or

 

GAME IN or VCR/DVR IN jacks, for the remote

 

controller to work properly, you must set the input

 

display.

 

 

 

If you cannot operate it, you will need to enter the

84

appropriate remote control code.

 

 

 

Page 94
Image 94
Onkyo TX-NR1008 instruction manual There’s no picture from a source connected to an Hdmi, On-screen menus don’t appear