Onkyo TX-NR1008 Setting the Powered Zone 2/3, Setting the Multi Zone, Enter, Zone2 Out, Zone3 Out

Setting the Powered Zone 2/3

If you’ve connected your Zone 2/3 speakers to the AV receiver, as explained in “Connecting Your Zone 2 Speak- ers Directly to the AV receiver” (➔ 73) or “Connecting Your Zone 3 Speakers Directly to the AV receiver”

(➔ 74), you must set the “Powered Zone2” or “Powered Zone3” setting to “Act” (Activated).

1 Press RECEIVER followed by SETUP.

The main menu appears onscreen.

Tip

•If the main menu doesn’t appear, make sure the appropri- ate external input is selected on your TV.

2 Use q/wto select “Speaker Setup”, and then press

ENTER.

The “Speaker Setup” menu appears.

2. Speaker Setup

1.Speaker Settings

2.Speaker Configuration

3.Speaker Distance

4.Level Calibration

5.Equalizer Settings

6.THX Audio Setup

3 Use q/wto select “Speaker Settings”, and then press ENTER.

The “Speaker Settings” menu appears.

		2–1. Speaker Settings
	Speaker Impedance		6ohms
	Speakers Type(Front)		Normal
	Powered Zone2		Not Act
	Powered Zone3		Not Act
4 Use q/wto select “Powered Zone2” or “Powered
Zone3”, and use e/rto select:
`Not Act:

FRONT WIDE/ZONE 2 L/R or FRONT

HIGH/ZONE 3 L/R speaker terminals not activated (Powered Zone 2/3 disabled).

`Act:

FRONT WIDE/ZONE 2 L/R or FRONT

HIGH/ZONE 3 L/R speaker terminals acti- vated (Powered Zone 2/3 enabled).

5 Press SETUP.

The setup menu closes.

Note

•Powered Zone 2 cannot be used if “Speakers Type(Front)” is set to “Bi-Amp” (➔ 47).

•This procedure can also be performed on the AV receiver by using SETUP, arrows, and ENTER.

Setting the Multi Zone

1 Press RECEIVER followed by SETUP.

The main menu appears onscreen.

Tip

•If the main menu doesn’t appear, make sure the appropri- ate external input is selected on your TV.

2 Use q/wto select “Hardware Setup”, and then press ENTER.

The “Hardware Setup” menu appears.

7.Hardware Setup

1.Remote ID

2.Multi Zone

3.Tuner

4.HDMI

5.Auto Power Down

6.Network

7.Firmware Update

3 Use q/wto select “Multi Zone”, and then press

ENTER.

The “Multi Zone” menu appears.

	7-2. Multi Zone
	Zone2 Out	Fixed
	Zone2 Maximum Volume	Off
	Zone2 Power On Volume	Last
	Zone3 Out	Fixed
	Zone3 Maximum Volume	Off
	Zone3 Power On Volume	Last
4 Use q/wto select an item, and use e/r			to change
it.
The items are explained below.
5 Press SETUP.
The setup menu closes.

Note

•This procedure can also be performed on the AV receiver by using SETUP, arrows, and ENTER.

■Zone2 Out, Zone3 Out

`Fixed:

The Zone 2/3 volume must be set on the amp in that zone.

`Variable:

The Zone 2/3 volume can be set on the AV receiver. If you’ve connected your Zone 2/3 speakers to an amp with no volume control, set the “Zone2 Out” and “Zone3 Out” setting, respectively, to “Variable” so that you can set the volume, balance, and tone of zone 2 and volume of zone 3 on the AV receiver.

■Zone2 Maximum Volume, Zone3 Maximum Volume

`Off, 50 to 99 (Absolute display)

`Off, –32dBto +17dB (Relative display)

With this setting, you can limit the maximum volume for Zone 2/3.

■ Zone2 Power On Volume,

Zone3 Power On Volume

`Last, Min, 1 to 99 or Max (Absolute display)

`Last, –QdB, –81dBto +18dB (Relative display)

This setting determines what the volume will be for	En
Zone 2/3 each time the AV receiver is turned on.
	75