Onkyo TX-NR1008 Recording, Zone 2/3, Music Server and Internet Radio, Others, Can’t record

To control another manufacturer’s component, point	86
the remote controller at that component.
If none of the codes work, use the Learning function	90
to learn the commands of the other component’s
remote controller.
To control an Onkyo component that’s connected via	86
u, point the remote controller at the AV receiver.
Be sure to enter the appropriate remote control code
first.
To control an Onkyo component that’s not connected	86
via u, point the remote controller at the compo-
nent. Be sure to enter the appropriate remote control
code first.

The entered remote control code may not be correct. — If more than one code is listed, try each one.

■Can’t learn commands from another remote controller

When learning commands, make sure that the trans- — mitting ends of both remote controllers are pointing

at each other.

Are you trying to learn from a remote controller that — cannot be used for learning? Some commands can- not be learned, especially those that contain several instructions.

Recording

■ Can’t record

On your recorder, make sure the correct input is	—
selected.
To prevent signal loops and damage to the AV	—
receiver, input signals are not fed through to outputs
with the same name (VCR/DVR IN to VCR/DVR
OUT).
When the Pure Audio listening mode is selected,	—
recording is not possible because no video signals
are output. Select another listening mode.

Zone 2/3

■There’s no sound

Only components connected to analog inputs can be — played in Zone 2/3.

■The Zone 2/3 speakers produce no sound

Powered Zone 2 cannot be used if “Speakers	47
Type(Front)” is set to “Bi-Amp”.
To use the Zone 2 speakers, you must set the “Pow-	75
ered Zone 2” setting to “Act”.
To use the Zone 3 speakers, you must set the “Pow-	75
ered Zone 3” setting to “Act”.

Music Server and Internet Radio

■Can’t access the server or Internet radio

Check the network connection between the AV	—
receiver and your router or switch.

Make sure that your modem and router are properly — connected, and make sure they are both turned on.

Make sure the server is up and running and compati- 68 ble with the AV receiver.

Check the “Network Settings”. 69

■Playback stops while listening to music files on the server

Make sure your server is compatible with the AV	68
receiver.
If you download or copy large files on your com-	—
puter, playback may be interrupted. Try closing any
unused programs, use a more powerful computer, or
use a dedicated server.
If the server is serving large music files to several	—
networked devices simultaneously, the network may
become overloaded and playback may be inter-
rupted. Reduce the number of playback devices on
the network, upgrade your network, or use a switch
instead of a hub.

■Can’t connect to the AV receiver from a Web browser

If you’re using DHCP, your router may not always	70
allocate the same IP address to the AV receiver, so if
you find that you can’t connect to a server or Internet
radio station, recheck the AV receiver’s IP address
on “Network” screen.
Check the “Network Settings”.	69

USB Mass Storage Device Playback

■Can’t access the music files on a USB device

Make sure the USB device is plugged in properly. —

The AV receiver supports USB devices that support — the USB mass storage device class. However, play- back may not be possible with some USB devices even if they conform to the USB mass storage device class.

USB memory devices with security functions cannot — be played.

Others

■ Stand-by power consumption

In the following cases, the power consumption may		58, 69,
reach up to a maximum of 55W:		81
1.	You are using the Universal Port jack.
2.	“Control” is set to “Enable” in the “Network”
	setting.
3.	“HDMI Control (RIHD)” setting is set to
	“On”. (Depending on the TV status, the AV
	receiver will enter Standby mode as usual.)

■ The sound changes when I connect my headphones

When a pair of headphones is connected, the listen- — ing mode is set to Stereo, unless it’s already set to Stereo, Mono, Direct, or Pure Audio.

■The speaker distance cannot be set as required

In some cases, corrected values suitable for home	—
theater use may be set automatically.

■ The display doesn’t work

The display is turned off when the Pure Audio listen- —	En
ing mode is selected.	95