Onkyo TX-NR717 En-56, Surround Back Ch, LPF of LFE Low-PassFilter for the LFE Channel, Unit

*6 When the “Powered Zone 3” setting is set to “Yes”, this setting cannot be selected.

■Surround Back Ch

`1ch:

Select if only one surround back speaker L is connected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

•If the “Surround Back” setting is set to “None”, this setting cannot be selected.

■LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

`Off:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

■Subwoofer Phase

`0º

`180º:

Moves the subwoofer phase.

Note

•If the “Subwoofer” setting is set to “No”, this setting cannot be selected.

■Double Bass

This setting is NOT set automatically by

Audyssey 2EQ® Room Correction and Speaker Setup (➔ page 35).

`On

`Off(THX)

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

•When the “Subwoofer” setting is set to “No” or the “Front” setting to anything other than “Full Band”, this setting is fixed to “- - - - -”.

•This setting is set to “On” automatically when the “Subwoofer” and “Front” settings are set for the first time to “Yes” and “Full Band” respectively.

•If you’re using THX-certified speakers, select “Off(THX)”.

Speaker Distance

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup (➔ page 35).

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

■Unit

`feet:

Distances can be set in feet. Range: 0.5ft to 30.0ft in

0.5foot steps.

`meters:

Distances can be set in meters. Range: 0.15m to 9.00m in 0.15 meter steps.

(The default setting varies from country to country.)

■Left, Front Wide Left, Front High Left, Center, Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left, Subwoofer

`Specify the distance from each speaker to your listening position.

En-56

Advanced Operations

Note

•Speakers that you set to “No” or “None” in

“Speaker Configuration” cannot be selected (➔ page 55).

•When the “Powered Zone 2” setting is set to “Yes” and Zone 2 is turned on, the surround back and front high speakers cannot be used.

•When the “Powered Zone 3” setting is set to “Yes” and Zone 3 is turned on, the surround and surround back speakers cannot be used.

Level Calibration

This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup (➔ page 35).

Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

Note

•These settings cannot be calibrated in either of the following cases:

–The “Audio TV Out” setting is set to “On” (➔ page 67).

–“HDMI Control(RIHD)” is set to “On” (➔ page 67) and you’re listening through your TV speakers.

–The AV receiver is muted.

■Left, Front Wide Left, Front High Left, Center*1,

Front High Right, Front Wide Right, Right, Surround Right, Surround Back Right, Surround Back Left, Surround Left

`–12.0dBto 0.0dB to +12.0dB in 0.5 dB steps.

■Subwoofer*1

`–15.0dBto 0.0dB to +12.0dB in 0.5 dB steps.

Note

•Speakers that you set to “No” or “None” in

“Speaker Configuration” cannot be selected (➔ page 55).

To be continued