Connecting Your
■Audio Signals
For TX-SR506
•Audio and video signals received via inputs other than the HDMI IN jacks are not output by the HDMI OUT.
•Audio and video signals received via the HDMI IN jacks are output only by the HDMI OUT.
•To watch an HDMI source that’s connected via the AV receiver’s HDMI jacks, the AV receiver must be turned on, otherwise no HDMI signal will be output.
•If you want to listen through the speakers connected to the AV receiver, in addition to an HDMI connection, you’ll also need to make a separate analog or digital audio connection.
For TX-SR576
•Digital audio signals received by the HDMI IN jacks are output by the speakers and headphones connected to the AV receiver.
•To listen to audio received by the HDMI IN jacks through your TV’s speakers, set the AudioTVOut setting to On (see pages
DVD player
Step 3 ✽
HDMI | HDMI |
OUT | IN |
| TV |
Step 2 | Step 1 |
IN 1 |
|
HDMI
ASSIGNABLE
Connect one or the other
| HDMI | IN 3 | IN 2 |
| ASSIGNABLE |
|
|
DIGITAL IN | COMPONENT VIDEO |
|
|
|
| Y |
1 |
|
|
|
(DVD) |
|
|
|
COAXIAL |
|
| CB/ PB |
|
|
| |
2 |
|
|
|
(CBL/SAT) |
|
|
|
|
|
| CR/ PR |
1 |
|
|
|
(VCR/DVR) |
|
|
|
OPTICAL | IN 1(DVD) | OUT |
|
IN 2 |
| ||
2 | ASSIGNABLE |
|
|
|
|
| |
(CD) | IN | OUT | IN |
| |||
ASSIGNABLE |
|
|
|
| L |
|
|
| R |
|
|
REMOTE |
|
|
|
CONTROL |
|
|
|
| CD |
| TAPE |
IN 1 | OUT |
|
|
|
|
|
|
|
|
| AM |
CBL/SAT | VCR/DVR | DVD | MONITOR |
| |
OUT |
| ||||
V |
|
|
|
| V |
|
|
|
|
| ANTENNA |
|
|
|
|
| FM |
S |
|
|
|
| 75 |
|
|
|
| S | |
IN | OUT | IN | IN |
|
|
IN | OUT | IN | FRONT | SURR | CENTER SURR BACK |
L |
|
|
|
| L |
R |
|
|
|
| R |
|
|
|
|
| SUB |
CBL/SAT | VCR/DVR |
| DVD | WOOFER | |
|
|
Tip!
If you make the connection described in step 3, to fully enjoy the AV receiver's lis- tening modes, turn down the volume on your TV all the way so that its speakers output no sound.
Sound off
Notes:
•The HDMI video stream is compatible with DVI (Digital Visual Interface), so TVs and displays with a DVI input can be connected by using an
•When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.
•The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details.
29