Ositech comm Trumpcard Data/Fax Modem instruction

Trumpcard Data/Fax Modem

User’s Guide and Reference

Image 1

Ositech comm Trumpcard Data/Fax Modem manual User’s Guide and Reference

Contents

User’s Guide and Reference Trumpcard Data/Fax Modem Copyright How To Contact UsFTP Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode Features Cellular Mode Facsimile Mode Unique Features 22bis Industry Standards32bis MNP 2, 3, 42bisMNP 27ter Preparing for Installation Hardware Installation Installing the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You Begin Operating the Trumpcard Using AT Commands Tone or Pulse Dialling Making an Outgoing Call Storing a Number Re-Dialling the Last NumberConnection Messages FAX Connect 1200TX/75RXData Carrier Ending Your Connection Setting Up for a Non-Error Correcting Connection Receiving an Incoming Call Setting up for a Cellular Connection Modem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command Summary Modem Command Reference Re-execute Modem Command DescriptionsAnswer Dn Dial Bn Set ITU-T or Bell ModeATB0 ATB1 ATDS=2 Fn Select Line Modulation 14400 only En Command Echo Sub-parameter Definitions +Ms Select Line Modulation 28800 only VFC Hn Switch-Hook ControlATH0 ATH1 Olume IdentificationMn Speaker Control On Return To The On-Line State Nn Automode Detection Qn Result Code Display Set Pulse Dial as DefaultSn Read/Write S Registers ATQ0 Vn Result Code Form Set Tone Dial as DefaultWn Connect Message Control Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Yn Control Long Space Disconnect Zn ResetCn DCD Option Dn DTR Option Restore Factory ConfigurationNone Jn T elephone Jack Selection Gn Set Guard ToneKn DTE/Modem Flow Control Pn Dial Pulse Ratio disabled for the U.S Mn Communication ModeQn Communication Mode Ln Line Type Sn DSR Option Rn RTS/CTS Option Tn T est and Diagnostic AT&T6 View Configuration and User ProfilesAT&T7 AT&T8 Wn Store User Profile Yn Designate Default User Profile \Bn T ransmit Break Zn=x Store Phone Number\Gn Modem-to-Modem Flow Control \Kn Break Control AT\K3 AT\K1AT\K5 Cn Compression Control \Nn Operation Mode Control Report Received Signal Level En Enable/Disable Line Quality MonitorReport Line Signal Quality Mn T ransmit Level Adjustment for Cellular Connection Kn MNP Extended ServicesHn Link Negotiation Speed En Compromise Equalizer @Mn Initial Cellular Power Level Init string = Null Init string Event Based Command Modem S Registers Default Register SettingsModem Register Summary Modem Command Reference S95 Extended Result Codes Register Descriptions S6 Wait S5 Backspace CharacterS7 Wait For Carrier After Dial S8 Pause S9 Carrier Detect Response Time S10 Lost Carrier To Hang Up DelayS11 Dtmf T one Duration S12 Escape Code Guard Time S24 Sleep Inactivity Timer S18 Test TimerS25 Delay to DTR S30 Inactivity Timer S33 Xoff Character S32 XON CharacterS36 Lapm Failure Control S37 Desired Telco Line Speed Range Default S46 Protocol Selection S38 Delay Before Forced Disconnect S86 Connection Failure Cause Code S48 V .42 Negotiation Action S95 Extended Result Codes Class 1 Commands Facsimile CommandsClass 2 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback Product Information Testing Modem MemoryROM Checksum Test