Kn MNP Extended Services | Ositech comm Trumpcard Data/Fax Modem

Modem Command Reference

Returns the high-order byte of the calculated Eye Quality Monitor (EQM) value. The value for a normal connection ranges from about 0 to 2 and approaches 8 for a progressively poorer connection.

-Kn — MNP Extended Services

Parameters

0, 1 or 2

Default1

Enables the modem to investigate the capabilities of the modem's MNP10 capacity, and determine whether a V.42 LAPM connection will be converted to an MNP connection. When -K1 is set on both modems, a LAPM connection will be converted to an MNP10 connection.

Examples

AT-K0	Disable V.42 LAPM to MNP 10 conversion
AT-K1	Enable V.42	LAPM to MNP 10 conversion
AT-K2	Enable V.42	LAPM to MNP 10 conversion; inhibit
	MNP extended services initiation during V.42 LAPM
	detection phase
*Hn — Link Negotiation Speed
Parameters	0, 1 or 2
Default	0

Sets the connection speed for link negotiation before upshift occurs between modems. When poor telephone lines are anticipated, the *H1 command should be used to set the connection speed to 1200 bps to facilitate link negotiation. If this command is set to a 1 and the modem connects in LAPM, the connection speed will be fixed at 1200 bps.

Examples

AT*H0	Link negotiation occurs at the preferred line speed
AT*H1	Link negotiation occurs at 1200 bps
AT*H2	Link negotiation occurs at 4800 bps

)Mn — T ransmit Level Adjustment for Cellular Connection

Parameters

0 or 1

Default0

User’s Guide and Reference

4 - 31

Image 63

Ositech comm Trumpcard Data/Fax Modem manual Kn MNP Extended Services, Hn Link Negotiation Speed

Contents

User’s Guide and Reference Trumpcard Data/Fax Modem How To Contact Us CopyrightFTP Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode Features Cellular Mode Facsimile Mode Unique Features Industry Standards 22bis32bis 27ter 42bisMNP 2, 3, MNP Preparing for Installation Hardware Installation Installing the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You Begin Operating the Trumpcard Using AT Commands Tone or Pulse Dialling Making an Outgoing Call Re-Dialling the Last Number Storing a NumberConnection Messages Carrier Connect 1200TX/75RXFAX Data Ending Your Connection Setting Up for a Non-Error Correcting Connection Receiving an Incoming Call Setting up for a Cellular Connection Modem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command Summary Modem Command Reference Modem Command Descriptions Re-executeAnswer ATB1 Bn Set ITU-T or Bell ModeDn Dial ATB0 ATDS=2 Fn Select Line Modulation 14400 only En Command Echo Sub-parameter Definitions +Ms Select Line Modulation 28800 only ATH1 Hn Switch-Hook ControlVFC ATH0 Identification OlumeMn Speaker Control On Return To The On-Line State Nn Automode Detection ATQ0 Set Pulse Dial as DefaultQn Result Code Display Sn Read/Write S Registers Set Tone Dial as Default Vn Result Code FormWn Connect Message Control Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Zn Reset Yn Control Long Space DisconnectCn DCD Option Restore Factory Configuration Dn DTR OptionNone Gn Set Guard Tone Jn T elephone Jack SelectionKn DTE/Modem Flow Control Ln Line Type Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Qn Communication Mode Sn DSR Option Rn RTS/CTS Option Tn T est and Diagnostic AT&T8 View Configuration and User ProfilesAT&T6 AT&T7 Wn Store User Profile Yn Designate Default User Profile \Kn Break Control Zn=x Store Phone Number\Bn T ransmit Break \Gn Modem-to-Modem Flow Control AT\K1 AT\K3AT\K5 Cn Compression Control \Nn Operation Mode Control En Enable/Disable Line Quality Monitor Report Received Signal LevelReport Line Signal Quality Kn MNP Extended Services Mn T ransmit Level Adjustment for Cellular ConnectionHn Link Negotiation Speed En Compromise Equalizer @Mn Initial Cellular Power Level Init string = Null Init string Event Based Command Default Register Settings Modem S RegistersModem Register Summary Modem Command Reference S95 Extended Result Codes Register Descriptions S8 Pause S5 Backspace CharacterS6 Wait S7 Wait For Carrier After Dial S12 Escape Code Guard Time S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S11 Dtmf T one Duration S30 Inactivity Timer S18 Test TimerS24 Sleep Inactivity Timer S25 Delay to DTR S32 XON Character S33 Xoff CharacterS36 Lapm Failure Control S37 Desired Telco Line Speed Range Default S46 Protocol Selection S38 Delay Before Forced Disconnect S86 Connection Failure Cause Code S48 V .42 Negotiation Action S95 Extended Result Codes Facsimile Commands Class 1 CommandsClass 2 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback Testing Modem Memory Product InformationROM Checksum Test