Zn=x Store Phone Number | Ositech comm Trumpcard Data/Fax Modem

Modem Command Reference

&Zn=x — Store Phone Number

Parameters

n = 0, 1, 2, or 3, x = dial string

Defaultnone

Stores a 36-digit dial string (x) in the specified entry (n) for later dialling. (See DSn command.)

\Bn — T ransmit Break

Parameters	1 through 9 (If n = 0, the default value is used; if n is
	greater than 9, 9 is used.)
Default	3

When this command is entered during a non-error correction connection, the modem sends a break signal to the remote modem. The length of the break is 100 times the n parameter value in milliseconds. If this command is entered during an error-correcting connection, the break will be sent via the error-correcting protocol giving no indication of length.

Result Codes

NO CARRIER

If not connected

\Gn — Modem-to-Modem Flow Control

Parameters

0 or 1

Default0

The command applies in non-error correction mode; the modem enables or disables the generation or recognition of modem-to-modem XON/XOFF flow control.

Examples

AT\G0	Disables modem-to-modem flow control
AT\G1	Enables modem-to-modem flow control
\Kn — Break Control
Parameters	0 through 5 (If n is greater than 5, 5 is used.)
Default	5

Determines what the modem will do when a BREAK is received from the communications software or the remote modem. During error correction mode, the remote modem's BREAK control setting determines how the local modem will handle the BREAK.

User’s Guide and Reference

4 - 27

Image 59

Ositech comm Trumpcard Data/Fax Modem manual Zn=x Store Phone Number, Bn T ransmit Break, Gn Modem-to-Modem Flow Control

Contents

User’s Guide and Reference Trumpcard Data/Fax Modem FTP How To Contact UsCopyright Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode Features Cellular Mode Facsimile Mode Unique Features 32bis Industry Standards22bis 27ter 42bisMNP 2, 3, MNP Preparing for Installation Hardware Installation Installing the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You Begin Operating the Trumpcard Using AT Commands Tone or Pulse Dialling Making an Outgoing Call Connection Messages Re-Dialling the Last NumberStoring a Number Carrier Connect 1200TX/75RXFAX Data Ending Your Connection Setting Up for a Non-Error Correcting Connection Receiving an Incoming Call Setting up for a Cellular Connection Modem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command Summary Modem Command Reference Answer Modem Command DescriptionsRe-execute ATB1 Bn Set ITU-T or Bell ModeDn Dial ATB0 ATDS=2 Fn Select Line Modulation 14400 only En Command Echo Sub-parameter Definitions +Ms Select Line Modulation 28800 only ATH1 Hn Switch-Hook ControlVFC ATH0 Mn Speaker Control IdentificationOlume On Return To The On-Line State Nn Automode Detection ATQ0 Set Pulse Dial as DefaultQn Result Code Display Sn Read/Write S Registers Wn Connect Message Control Set Tone Dial as DefaultVn Result Code Form Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Cn DCD Option Zn ResetYn Control Long Space Disconnect None Restore Factory ConfigurationDn DTR Option Kn DTE/Modem Flow Control Gn Set Guard ToneJn T elephone Jack Selection Ln Line Type Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Qn Communication Mode Sn DSR Option Rn RTS/CTS Option Tn T est and Diagnostic AT&T8 View Configuration and User ProfilesAT&T6 AT&T7 Wn Store User Profile Yn Designate Default User Profile \Kn Break Control Zn=x Store Phone Number\Bn T ransmit Break \Gn Modem-to-Modem Flow Control AT\K5 AT\K1AT\K3 Cn Compression Control \Nn Operation Mode Control Report Line Signal Quality En Enable/Disable Line Quality MonitorReport Received Signal Level Hn Link Negotiation Speed Kn MNP Extended ServicesMn T ransmit Level Adjustment for Cellular Connection En Compromise Equalizer @Mn Initial Cellular Power Level Init string = Null Init string Event Based Command Modem Register Summary Default Register SettingsModem S Registers Modem Command Reference S95 Extended Result Codes Register Descriptions S8 Pause S5 Backspace CharacterS6 Wait S7 Wait For Carrier After Dial S12 Escape Code Guard Time S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S11 Dtmf T one Duration S30 Inactivity Timer S18 Test TimerS24 Sleep Inactivity Timer S25 Delay to DTR S36 Lapm Failure Control S32 XON CharacterS33 Xoff Character S37 Desired Telco Line Speed Range Default S46 Protocol Selection S38 Delay Before Forced Disconnect S86 Connection Failure Cause Code S48 V .42 Negotiation Action S95 Extended Result Codes Class 2 Commands Facsimile CommandsClass 1 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback ROM Checksum Test Testing Modem MemoryProduct Information