Ositech comm Trumpcard Data/Fax Modem specification

Section Four

4 - 12

Trumpcard 14400/28800 Modem

Image 32

Ositech comm Trumpcard Data/Fax Modem manual Section Four Trumpcard 14400/28800 Modem

Contents

Trumpcard Data/Fax Modem User’s Guide and Reference FTP How To Contact UsCopyright Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Features Data Mode Facsimile Mode Cellular Mode Unique Features 32bis Industry Standards22bis 42bis MNP 2, 3,MNP 27ter Hardware Installation Preparing for Installation Installing the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Before You Begin Enabling The Trumpcard Using AT Commands Operating the Trumpcard Making an Outgoing Call Tone or Pulse Dialling Connection Messages Re-Dialling the Last NumberStoring a Number Connect 1200TX/75RX FAXData Carrier Setting Up for a Non-Error Correcting Connection Ending Your Connection Setting up for a Cellular Connection Receiving an Incoming Call Modem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference Modem Command Summary +MS Modem Command Reference Answer Modem Command DescriptionsRe-execute Bn Set ITU-T or Bell Mode Dn DialATB0 ATB1 ATDS=2 En Command Echo Fn Select Line Modulation 14400 only +Ms Select Line Modulation 28800 only Sub-parameter Definitions Hn Switch-Hook Control VFCATH0 ATH1 Mn Speaker Control IdentificationOlume Nn Automode Detection On Return To The On-Line State Set Pulse Dial as Default Qn Result Code DisplaySn Read/Write S Registers ATQ0 Wn Connect Message Control Set Tone Dial as DefaultVn Result Code Form Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Cn DCD Option Zn ResetYn Control Long Space Disconnect None Restore Factory ConfigurationDn DTR Option Kn DTE/Modem Flow Control Gn Set Guard ToneJn T elephone Jack Selection Mn Communication Mode Pn Dial Pulse Ratio disabled for the U.SQn Communication Mode Ln Line Type Rn RTS/CTS Option Sn DSR Option Tn T est and Diagnostic View Configuration and User Profiles AT&T6AT&T7 AT&T8 Yn Designate Default User Profile Wn Store User Profile Zn=x Store Phone Number \Bn T ransmit Break\Gn Modem-to-Modem Flow Control \Kn Break Control AT\K5 AT\K1AT\K3 \Nn Operation Mode Control Cn Compression Control Report Line Signal Quality En Enable/Disable Line Quality MonitorReport Received Signal Level Hn Link Negotiation Speed Kn MNP Extended ServicesMn T ransmit Level Adjustment for Cellular Connection @Mn Initial Cellular Power Level En Compromise Equalizer Init string Event Based Command Init string = Null Modem Register Summary Default Register SettingsModem S Registers Modem Command Reference S95 Extended Result Codes Register Descriptions S5 Backspace Character S6 WaitS7 Wait For Carrier After Dial S8 Pause S10 Lost Carrier To Hang Up Delay S9 Carrier Detect Response TimeS11 Dtmf T one Duration S12 Escape Code Guard Time S18 Test Timer S24 Sleep Inactivity TimerS25 Delay to DTR S30 Inactivity Timer S36 Lapm Failure Control S32 XON CharacterS33 Xoff Character Range Default S37 Desired Telco Line Speed S38 Delay Before Forced Disconnect S46 Protocol Selection S48 V .42 Negotiation Action S86 Connection Failure Cause Code S95 Extended Result Codes Class 2 Commands Facsimile CommandsClass 1 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback ROM Checksum Test Testing Modem MemoryProduct Information