Connect 1200TX/75RX | Ositech comm Trumpcard Data/Fax Modem instruction

Section Four
Short	Long	Description
Form	Form
12	CONNECT 9600	connection at 9600 bps
13	CONNECT 7200	connection at 7200 bps
14	CONNECT 12000	connection at 12000 bps
15	CONNECT 14400	connection at 14400 bps
16	CONNECT 19200	connection at 19200 bps
17	CONNECT 38400	connection at 38400 bps
18	CONNECT 57600	connection at 57600 bps
19	CONNECT 115200	connection at 115200 bps *

22CONNECT 75TX/1200RX originated a connection with Modem supporting V.23

23	CONNECT 1200TX/75RX	answered a connection with
		Modem supporting V.23
33	FAX	fax mode connection
35	DATA	data mode connection
40	CARRIER 300	carrier signal detected at 300 bps

44CARRIER 1200/75 V.23 backward channel carrier detected

45CARRIER 75/1200 V.23 forward channel carrier detected

46	CARRIER 1200	carrier signal detected at 1200 bps
47	CARRIER 2400	carrier signal detected at 2400 bps
48	CARRIER 4800	carrier signal detected at 4800 bps
49	CARRIER 7200	carrier signal detected at 7200 bps
50	CARRIER 9600	carrier signal detected at 9600
		bps
51	CARRIER 12000	carrier signal detected at 12000
		bps
52	CARRIER 14400	carrier signal detected at 14400
		bps
53	CARRIER 16800	carrier signal detected at 16800
		bps *
54	CARRIER 19200	carrier signal detected at 19200
		bps *
55	CARRIER 21600	carrier signal detected at 21600
		bps *
56	CARRIER 24000	carrier signal detected at 24000
		bps *
57	CARRIER 26400	carrier signal detected at 264000
		bps *
58	CARRIER 28800	carrier signal detected at 28800
		bps *
59	CARRIER 16800	carrier signal detected at 16800
		bps *
61	CONNECT 21600	connection at 21600 bps *
	* Only applicable	to Trumpcard 28800 version

4 - 6

Trumpcard 14400/28800 Modem

Image 26

Ositech comm Trumpcard Data/Fax Modem manual Connect 1200TX/75RX, Carrier

Contents

Trumpcard Data/Fax Modem User’s Guide and Reference FTP How To Contact UsCopyright Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Features Data Mode Facsimile Mode Cellular Mode Unique Features 32bis Industry Standards22bis MNP 42bisMNP 2, 3, 27ter Hardware Installation Preparing for Installation Installing the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Before You Begin Enabling The Trumpcard Using AT Commands Operating the Trumpcard Making an Outgoing Call Tone or Pulse Dialling Connection Messages Re-Dialling the Last NumberStoring a Number Data Connect 1200TX/75RXFAX Carrier Setting Up for a Non-Error Correcting Connection Ending Your Connection Setting up for a Cellular Connection Receiving an Incoming Call Modem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference Modem Command Summary +MS Modem Command Reference Answer Modem Command DescriptionsRe-execute ATB0 Bn Set ITU-T or Bell ModeDn Dial ATB1 ATDS=2 En Command Echo Fn Select Line Modulation 14400 only +Ms Select Line Modulation 28800 only Sub-parameter Definitions ATH0 Hn Switch-Hook ControlVFC ATH1 Mn Speaker Control IdentificationOlume Nn Automode Detection On Return To The On-Line State Sn Read/Write S Registers Set Pulse Dial as DefaultQn Result Code Display ATQ0 Wn Connect Message Control Set Tone Dial as DefaultVn Result Code Form Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Cn DCD Option Zn ResetYn Control Long Space Disconnect None Restore Factory ConfigurationDn DTR Option Kn DTE/Modem Flow Control Gn Set Guard ToneJn T elephone Jack Selection Qn Communication Mode Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Ln Line Type Rn RTS/CTS Option Sn DSR Option Tn T est and Diagnostic AT&T7 View Configuration and User ProfilesAT&T6 AT&T8 Yn Designate Default User Profile Wn Store User Profile \Gn Modem-to-Modem Flow Control Zn=x Store Phone Number\Bn T ransmit Break \Kn Break Control AT\K5 AT\K1AT\K3 \Nn Operation Mode Control Cn Compression Control Report Line Signal Quality En Enable/Disable Line Quality MonitorReport Received Signal Level Hn Link Negotiation Speed Kn MNP Extended ServicesMn T ransmit Level Adjustment for Cellular Connection @Mn Initial Cellular Power Level En Compromise Equalizer Init string Event Based Command Init string = Null Modem Register Summary Default Register SettingsModem S Registers Modem Command Reference S95 Extended Result Codes Register Descriptions S7 Wait For Carrier After Dial S5 Backspace CharacterS6 Wait S8 Pause S11 Dtmf T one Duration S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S12 Escape Code Guard Time S25 Delay to DTR S18 Test TimerS24 Sleep Inactivity Timer S30 Inactivity Timer S36 Lapm Failure Control S32 XON CharacterS33 Xoff Character Range Default S37 Desired Telco Line Speed S38 Delay Before Forced Disconnect S46 Protocol Selection S48 V .42 Negotiation Action S86 Connection Failure Cause Code S95 Extended Result Codes Class 2 Commands Facsimile CommandsClass 1 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback ROM Checksum Test Testing Modem MemoryProduct Information