Panasonic AG-DVC 200E Shutter speed, LOW Light warning, Display Audio sampling, Frequency display

Viewfinder displays

				ENGLISH
Display item		What is displayed	Status causing the display to appear
8 Shutter speed	1/¢¢.¢		Displayed when the shutter speed has been set to SYNCHRO SCAN.
	1/60 - 1/2000		Displayed when a fixed shutter speed has been set.
	SUPER V		Displayed when SUPER V (high vertical resolution mode) has been set.
9 LOW LIGHT warning	LOW LIGHT		Displayed when the brightness has been reduced.
display
: AUDIO sampling	48k		Indicates that a frequency of 48 kHz has been selected.
frequency display	32k		Indicates that a frequency of 32 kHz has been selected.
			<Note>
			With a 1394 input, the input status is displayed.
; Audio level meter			Indicates the audio levels of CH1 and CH2 (see page 27).
display
< VTR warning	REC WARNING		Indicates the occurrence of an error during recording.
display/voltage	SLACK E-¢¢		Indicates the occurrence of an error caused by the mechanism. Depending
warning display			on the type of error, the power may be cut off automatically. (*1)
			<Note>
			For details on the codes displayed, refer to “Error codes” (page 40).
	HUMID		Indicates that condensation has formed.
	SERVO		Servo lock is not engaged during recording or playback.
	RF		The signal level from the tape has dropped.
	TAPE NEAR END		The tape is nearing its end (there are about 2 minutes left).
	TAPE END		The tape has stopped at the tape end.
	BATT NEAR END		The battery is nearly flat.
	BATT END		The tape has stopped because the battery is flat.
	MP TAPE		An MP tape has been loaded. The tape is automatically ejected.
	BACKUP BATT EMPTY		It is time to replace the backup battery.
= FULL AUTO/SCENE	FULL		Displayed when the FULL AUTO switch has been set to ON.
FILE display	Filename which has been set		Indicates the filenames (8 characters) set for the scene files.
> AWB colour	AWB+¢¢		The adjustment amount is displayed when ON has been selected as the
temperature fine			“COLOUR TEMP” setting (see page 36) and the colour temperature has
adjustment amount			been adjusted finely. It is not displayed when OFF is selected or only ATW
display			has been set.
? Zoom display	Z00 - Z99		Indicates the zoom amount. However, most 1/2-inch size lenses have no
			zoom position return. In such a case, this item is not displayed even if ON
			has been selected as the display setting.
@ AWB colour	¢.¢K		Indicates the colour temperature.
temperature display
A ATW, AWB channel	Ach		The WHITE BAL switch has been set to channel A.
display	Bch		The WHITE BAL switch has been set to channel B.
	PRE		The WHITE BAL switch has been set to PRE.
	ATW		The full time auto white balance has been set.
B F value display	NC		Displayed when the lens cable has not been connected.
	OPEN		Displayed when the lens iris has been opened.
	F2.0 - F16		Indicates the lens iris value.
	CLOSE		Displayed when the lens iris has been closed.
			<Note>
			This item appears when using a lens equipped with a function that displays
			the aperture value.
C Gain display	0 - 36dB		Displays the current gain value.
D Filter display	FL1 - FL4		Displays the filter position.
	FL–		Displayed when filter has not been set to the proper position.
E Calendar/clock	01-May-01 00:00:00		The 24-hour system is used for the clock display.
display			(Day-month-year and hours-minutes-seconds displayed)
F Voltage display	¢¢.¢V		The input voltage is displayed.
BAR display	B ∫∫∫∫		The number of “∫” squares serves as a rough guideline to indicate how
			much battery charge remains. When the battery still has a sufficient charge,
			four of these squares are displayed. These squares can be displayed
			except when Type A or Type B has been selected as the <BATTERY
			SELECT> setting on the BATTERY sub-menu. (See page 34)

18 (E)