Setting the IP address
In most cases, default settings can normally be used without making any changes.
Set the IP address only when the router has no DHCP server functions or when the router’s DHCP server function is disabled.
After performing steps 1 – 3 (> 28)
4 Press [3, 4] to select “IP Address Auto Configuration (DHCP)” and press [2, 1] to select “Off”.
≥Generally leave “On” selected.
≥When “Off” is selected, “DNS Auto Configuration (DHCP)” (> below) is also automatically “Off”.
5 Press [3, 4] to select “IP Address”, “Subnet Mask” or “Default Gateway” and press [OK].
6 Enter numbers with the numbered buttons and press [OK].
≥If a wrong number is entered, then press [CANCEL].
7 Press [2, 1] to select “Yes” and press [OK].
≥After checking the specifications for your broadband router, enter each number. If the number is unknown, then check the number of other devices such as personal computers connected via a LAN cable. Assign a different number from those of other devices for the “IP Address” and the same number for others.
≥The numeric input range is between 0 and 255.
Setting the DNS-IP
In most cases, default settings can normally be used without making any changes.
When setting an assigned DNS server from your Internet service provider, perform the following settings.
After performing steps 1 – 3 (> 28)
4 Press [3, 4] to select “DNS Auto Configuration (DHCP)” and press [2, 1] to select “Off”.
5 Press [3, 4] to select “Primary DNS” or “Secondary DNS”and press [OK].
6 Enter numbers with the numbered buttons and press [OK].
Primary DNS
Please input Primary DNS and press
[OK]. Press [CANCEL] to delete the selected character. To clear this setting, delete all characters and press [OK].
192 | . | 1 |
| . |
| . |
0 | - | 9 | Number |
≥If a wrong number is entered, then press [CANCEL].
7 Press [2, 1] to select “Yes” and press [OK].
≥Follow the instructions given by your Internet service provider and enter the numbers. If the number is unknown, then check the number of other devices such as personal computers connected via a LAN cable and assign the same number.
≥The numeric input range is between 0 and 255.
Setting the connection speed
When the connection test results in “Fail” after the IP and DNS- IP addresses are assigned, perform the following settings.
After performing steps 1 – 3 (> 28)
4 Press [3, 4] to select “Auto Detect Connection Speed” and press [2, 1] to select “Off”.
5 Press [3, 4] to select “Connection Speed Setting” and press [2, 1] to select a connection speed.
≥Select a connection speed in accordance with the environment of the network connected.
≥When the settings are changed, the network connection may be slower or disabled depending on the device.
Testing of “Proxy Server Settings”
Always test the connection when new “Proxy Server Settings” have been made.
1 Press [SETUP].
2 Press [3, 4] to select “Network” and press [OK].
3 Press [3, 4] to select “Proxy Server Settings” and press [OK].
4 Press [3, 4] to select “Connection Test” and press [OK].
“Testing”: | The test is in progress. |
“Pass”: | The connection is completed. |
| Press [RETURN] to exit. |
“Fail”: | Please check the connection and settings. |
Setting the proxy server
In most cases, default settings can normally be used without making any changes.
Please use this setting when instructed to by your Internet service provider.
After performing steps 1 – 3 (D above)
4 Press [3, 4] to select “Proxy Address” and press [OK].
Proxy Server Settings
Reset to factory preset |
|
Proxy Address |
|
Proxy Port Number | 0 |
Connection Test |
OK
RETURN
Network
(Continued on the next page) | RQT9334 |
29 | |
| (ENG) |
