Manually programming timer recordings

You can enter up to 32 programs up to a month in advance. Each daily or weekly program is counted as one program.

1 Press [PROG/CHECK].

TIMER

 

Remain HDD 17:36 SP

DVD 1:42 SP

RECORDING

 

 

 

3/26 TUE 12:55 PM

 

 

 

 

 

No

CHANNEL

DATE

ON

OFF

MODE

DRIVE CHECK

01

64 ABC

3/ 26 TUE

1:00 PM

2:00 PM

SP

Enable

 

 

New Timer Program

 

 

SELECT

CANCEL Press ENTER or VCR Plus+ to

ENTER

RETURN

store new program.

2 Press [3, 4] to select “New Timer

Program” and press [ENTER].

TIMER

 

Remain HDD 17:36 SP DVD

1:42 SP

RECORDING

 

 

 

3/26 TUE 12:55 PM

 

 

 

 

 

 

CHANNEL

DATE

ON

OFF

MODE

DRIVE

 

3

----------

--:-- --

--:-- --

--

---

 

----4

 

 

 

 

 

Enter Title

 

 

Please set Channel.

 

 

SELECT

 

 

 

No.

 

 

 

 

0

-- 9

 

 

ENTER

RETURN

 

 

 

 

 

 

3 Press [1] to move through the items

and change the items with [3, 4].

The current settings are shown each time you press [1].

You may use the numbered buttons to enter the CHANNEL, DATE, ON (start Time), and OFF (Finish Time).

TIMER

 

 

 

 

RECORDING

Remain HDD

17:36 SP

DVD

1:42 SP

 

3/26 TUE 12:55 PM

 

 

CHANNEL DATE

ON

OFF MODE

DRIVE

64 ABC

3/ 26 TUE

2:30 PM

3:00 PM

SP

HDD

Enter Title

CHANNEL (Channel number and caption)

DATE

[.Current date

l;:

lNext day up to one month later minus one day

l;:

lWeekly timer: SUN-SAT>MON-SAT>MON-FRI

l;:

{.Daily timer: WEEKLY SUN>--->WEEKLY SAT

ON (Start time)/OFF (Finish time)

The time increases or decreases in 30-minute increments if you hold the button.

MODE (Recording mode page 15)

SP>XP>FR>EP>LP (>Return to SP)

DRIVE HDD()DVD

RENEW (page 28, Auto Renewal Recording)

Only when you set daily or weekly recording onto HDD –You cannot set if “MPEG4 Rec mode”( page 52) is set to

either “SF”, “F”, “N”, or “E”. ON()OFF

Enter Title

Select “Enter Title” using 2[ , 1] and press [ENTER] (page 46).

4 Press [ENTER] when you have finished programming the timer.

TIMER

 

Remain HDD 17:36 SP

DVD 1:42 SP

 

 

 

RECORDING

 

 

 

 

 

 

3/26 TUE 12:55 PM

Displayed if the

 

 

 

 

 

No

CHANNEL

DATE

ON

OFF

MODE

DRIVE CHECK

recording can fit

01

64 ABC

3/ 26 TUE

1:00 PM

2:00 PM

SP

Enable

02

64 ABC

3/ 26 TUE

2:30 PM

3:00 PM

SP

Enable

in the remaining

 

 

New Timer Program

 

 

space

on

the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

disc.

 

 

Press [3, 4] to select “New Timer Program” and repeat steps 2- 4 to program other recordings.

5 Press [PROG/CHECK] or [RETURN].

The timer recording list disappears and the unit enters Timer Recording standby mode (“F” appears on the unit display).

The unit is not off. To save power, turn the unit off by press- ing [Í, DVD POWER].

To release the unit from recording standby

Cancel all the timer recording programs using [CANCEL]

recording

(page 29).

 

To cancel recording when recording has

 

already begun

 

Press [], then [ENTER] within 5 seconds.

Timer

Recording stops.

 

[Note]

 

When the program timer reaches the set time when in record- ing standby mode, timer recording will start even if the unit is playing or recording another program.

The actual time recorded may be longer than the program itself when television programs are recorded using VCR Plusi.

If you don’t select a recording mode when using VCR Plus+ codes to make a timer recording, the unit sets the mode selected on the unit at that time (unless the mode is “XP”, in which case the unit sets “FR” as the mode).

“All timer programs are occupied.” appears if there are already 32 programs.

The remaining time displayed is based on the current record- ing mode.

When you program successive timer recordings to start immediately one after the other, the unit cannot record the part at the beginning of the later programs (a few seconds when recording with HDD or DVD-RAM, and approximately 30 seconds when recording with DVD-R).

If you set DST (Daylight Saving Time) to ON when manually setting the clock (page 55), timer recording may not work when summer switches to winter and vice versa.

F” flashes when the unit couldn’t go to timer recording standby.

When timer recording starts, the record lamp (page 13, Main unit) lights, even if the unit is off.

Relief Recording

When the recording drive is set to “DVD” for timer recording, the unit will automatically evaluate if the program will fit onto the disc before beginning recording. If the program will not fit then the recording drive will be altered to “HDD” automatically.

If the time remaining on the HDD is insufficient, as much of the program as possible will be recorded onto the HDD.

If there is no disc in the tray or the disc cannot be recorded on, the recording drive will be altered to HDD.

The recording mode will not be altered.

The Direct Navigator shows which programs were relief- recorded (page 19).

27

RQT6986

Page 27
Image 27
Panasonic DMR-E100H warranty Manually programming timer recordings