Manuals / Panasonic / Photography / Digital Camera

Panasonic KX-HCM250 operating instructions Click External Output Control on Setup

Models: KX-HCM250

1 132

Download 132 pages 29.24 Kb

Page 87

Operating Instructions

3.5.10 External Output Control

External Output Control window enables the External Device Control Output signal to activate the external sensors/devices. (Open or Short to GND) The network administrator should set up this setting.

Note

Refer to page 102 for Interfacing to the External I/O.

1.Click [External Output Control] on Setup Page.

2.Check [Open] means the External Device Control Output becomes high impedance (open collector).

Check [Short to GND] means the External Device Control Output becomes low (0V).

3.Click [Save] to send the signal.

•Click [Cancel] to quit the current settings. The window returns to Setup Page without saving the parameters.

[For assistance, please call: 1-800-272-7033]

87

Image 87

Panasonic KX-HCM250 operating instructions Click External Output Control on Setup

Contents

Network Camera For operation assistance Call IntroductionTrademarks Network Camera MemoFor assistance, please call Important Safety Instructions Table of Contents Specifications and Troubleshooting 107 Technical GuidesIndex 129 Section Getting to Know Network Camera Main FeaturesExternal I/O Input/Output Multi Client AccessUpdate Firmware AuthenticationSystem Requirements Authentication window Authentication-System Security FeatureFlexible Stand 1 pc Included AccessoriesSetup CD-ROM 1 pc AC Adaptor 1 pcSetup CD-ROM Front View Camera Feature LocationsIndicator Refer to page 88 for the setupBottom View Rear ViewNetwork Camera Setup Installation Procedure Network Camera Configuration Type Network Camera can be installed on the LAN/IntranetType 2-Internet Connection with a Broadband Router Type 4-Direct Connection with a PC Type 3-Internet Direct Connection with a ModemHow to turn on Network Camera for Installation Network Parameters Preparing the Network Parameters for Network CameraNetwork parameters memo for Network Camera Type Port No Network Camera Configuration TypeDefault Network Parameters TableClick OK to close IP Configuration window How to refer the network parameters from the PCSetting IP Address of the PC in Type 4 Configuration Type Private IP address Proxy Server Setting Operating Instructions Simple Installation using the Setup CD-ROM Operating Instructions Operating Instructions Click the language to change the display Wireless Setup To access Network windowTo set up the wireless network parameters Connection and Signal Strength status Set Infrastructure Default or AdHocChannel Encryption Key window Encryption Password windowWireless Settings Default KeyIf Top Page does not appear Port Forwarding IP Masquerade feature Network Camera Access from the InternetTop Network Camera Screen and Setup Window Network Camera Flow Chart Top ExampleHttp//Global IP address of Broadband RouterPortNo Top Help Motion JpegSingle Camera Multi-CameraActiveX Controls Single Camera Screen Click to Center Using Operation Bar Using Pan/Tilt Operation Setting Preset Positioning and Home Positioning Click Delete Deleting the preset buttonsViewing Buffered Image Screen Non Transfer mode Alarm/Timer modeSecondary ViewerClicking Start Capture PrimaryMulti-Camera Screen Setup Setup Name/Time AdministratorCamera Setup Go to TopEntered. If any operational issues are changed, try This option first. Refer toFunctions of Network Camera Go to Top Network Enter only the number Instructions for the data fieldsOr administrator for the Host name If you use Network Camera on the LAN, set upCheck Dhcp Dynamic Host Configuration Protocol Host Name When your ISP uses the Dhcp server function whichFile size of the image Date Name/TimeCamera NameTime Zone AdjustmentTime Changed AM/PM or 24H AutoSecurity Administrator Refer to page 65 for details about authentication securityClick Security Administrator on Setup Retype EnableAdministrator and General User Authentication window For Setup PasswordSecurity General User Click Security General User on SetupOperating Instructions Top View Image 160 x ResolutionInstructions for the data fields Top ImageImage Transfer Non Transfer mode Click Alarm on Image Transfer window Transfer in the Alarm ModeActive Time of Trigger Alarm enable conditionLogin timing Data transfer method Over write settingSetting Example Setting explanation Transfer in the Timer Mode Image Frequency Sets the interval to send the image Buffers or transfers by the timer triggerLogin timing Over write setting Fixed Camera SetupInstructions for the data fields White Balance Fixed IndoorTilt Range White Balance is also registered in preset programmingSuggested Having reached the selected endSpecifying the Pan/Tilt range Click Save when finishedMulti-Camera Camera Name Enable check boxIP Address or URL * 1 or HostExternal Output Control Click External Output Control on SetupIndicator Control Status Click Cancel to quit. The window returns to Setup RestartClick Restart Now Update Firmware Click Update Firmware Click Update Firmware on SetupOpen Reset to Factory Default Technical Guides High performance for wireless communication Network Camera InstallationNetwork Camera Mounting Hook for AC adaptor cordThread the AC adaptor cord through the hook before mounting Wall Mounting Ceiling Mounting Flexible Stand MountingTripod Mounting Attach Network Camera to the tripod by using the tripod boltTape Customer provided 100 Wall MountingCeiling Mounting External Sensor Input Interfacing to the External I/OExplanation of External I/O Pin FunctionCircuit Diagram Example 104 Ascii and ISO-8859-1 Character TableUnavailable character set Space, , , #, &, %, =, +, ?, , and are not availableFor assistance, please call 105 Displayable character set106 MaintenanceFor assistance, please call 107 Specifications and TroubleshootingNetwork Camera Reset Procedure-Default Settings For assistance, please call 109 Default Settings List110 For assistance, please call 111 Items Factory Default Indispensable setting Value Alarm112 TimerFor Call113 114 Control Indicator ControlSpecifications Network Camera Specifications DescriptionOther Specification Description AC adaptor Input 120 V AC, 60 Hz Weight 530 1.17 lb. Only the unitMm 3.46 inches Excluding the antenna and protruding objectsTroubleshooting About Network Camera SetupProblem Cause and Remedy For Indicator Control window Transfers older Network window onFirmware has About Network Camera Setup Problem Cause and RemedyUpdate Refer to page 91 for the Update Firmware 120Lens About Top View Image screenAbout Other Troubles View Image Setting window onConfirmation of Network Camera Operation Click the language to change the display FCC and Other Information Medical Ieee 802.11b GlossaryAdHoc Encryption WEP128 129 IndexOperating Instructions TCP/IP When you ship the product For product service